One-Touch Timer Recording (Otr); Timer Recording - Disney DVD2100-C User Manual

One-touch Timer Recording (OTR)

The One-touch Timer Recording feature provides a
simple and convenient way to make a timed recording.
Example: One-touch Timer Recording for 30 minutes.
1
Load a cassette tape with the erase prevention tab
intact.
The unit will automatically turn on.
2
Press Speed to select the desired tape speed SP or
SLP.
The tape counter and SP or SLP will appear on the
screen for about 4 seconds.
3
Set the TV/CABLE option to the appropriate position.
4
Press Number keys or
be recorded.
5
Press OTR Rec.. Press the button again to stop record-
ing after 30 minutes. Each additional press of OTR Rec.
will increase recording time as shown in the chart below,
up to a maximum of 6 hours. The OTR and recording time
will appear on the screen for about 4 seconds and the
Record indicator on the front panel will keep blinking.
Press
Recording time Press
once NORMAL REC
twice 0:30
3 times 1:00
4 times 1:30
5 times 2:00
To cancel OTR
Press Stop or turn off the power.
" " will appear on screen for about 4 seconds.
NOTE:
If you wish to watch the DVD playback during the OTR, press
VCR/DVD to change to DVD mode and perform the DVD
playback (see page 24).
20
+ / – to select the channel to
Recording time
3:00
6 times
7 times 4:00
5:00
8 times
6:00
9 times
NORMAL REC
10 times

Timer recording

Timer recording can be programmed on-screen with the
remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1 month.
Example: Program a timer recording for the 26th day,
channel 125 (CABLE), 11:00 - 11:30 PM on timer program
number 1 (Tape speed: SLP).
1
Press VCR Menu. Select the
"TIMER REC SET" option,
then press Enter.
2
Press Set + or – to select
one of the program line,
then press Enter.
3
Press Set + or – to select
the date, then press Enter.
4
Set the start time, end time,
channel and tape speed as
in step 3.
NOTE:
Press Cancel to move cursor backward for correction.
5
To enter other programs, repeat step 2 through 4.
• To return to the normal screen, press VCR Menu twice.
6
Press Timer Rec.. The Timer Record indicator will light
and the VCR stands by for recording. At the same time,
VCR mode will change to DVD mode automatically. You
can use DVD even if the VCR is in the Timer recording
mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 20 seconds before the
time you predetermined.
NOTE:
If the cassette is ejected in spite of the pressing of Timer
Rec., the erase prevention tab of the cassette may have
been removed. (see page 17)
NOTES:
• During timer recording standby mode, the VCR mode cannot
be selected. To use the VCR, press Timer Rec. at first, then
press VCR/DVD to change to VCR mode. After you use the
VCR, press Timer Rec. again to put the VCR into timer
recording standby mode.
• If you press Timer Rec. during timer recording, the record
ing operation will be interrupted. If you press Timer Rec.
again within the programmed time, the recording operation will
start again.
• After a power failure or disconnection of the power plug, all
programmed recording settings and time display will be lost
upon resumption of power. In this case, reset the clock (see
page 16) and reprogram any timer recordings.
MENU
TIMER REC SET
ON OFF
AUTO REPEAT
SAP ON OFF
CH SETUP
SYSTEM SETUP
+/-/ENTER/MENU
á ñ
DATE START END CH
26(SU) 11:00 11:30 125
PM PM SLP
+/-/ENTER/CANCEL/MENU
á ñ