VTech VM344 Quick Start Manual page 2

Overview - Parent unit
Light indicators
Microphone
Zoom
TALK
+ / VOL / -
Basic operation - Parent unit
Adjust speaker volume Pan, tilt, zoom
Press + / VOL / - to adjust your parent unit speaker Press and hold , , or to move the camera.
volume. It determines the volume of sound
transmitted from your baby unit.
Turn off the screen Use the menu
Press and hold LCD ON/OFF to turn off the screen. Press MENU/SELECT to enter the menu, choose
You can still hear sound from the selected baby unit. a menu item, or save a setting.
While in the menu:
• Press or to scroll up or down.
• Press to select an item.
• Press BACK to return to the main menu or
idle screen.
2s
At least 1 meter
On/off
VIEW / LCD ON/OFF
MENU/SELECT
(3 feet)
PATROL
SPLIT
Arrow keys
Talk to your baby unit
Press to zoom in or out. Press and hold TALK and speak to your parent unit. Your voice
is transmitted to the baby unit.
Long press
n a t h e o r M
) e t f e ( 3 e r e t m 1
Mount the baby monitor (optional)
Turn off the parent unit
Press and hold to power off your parent unit.
2s
NOTES
• Check for reception strength and
camera angle before drilling the holes.
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
Overview - Baby unit
Light sensor
Antenna
Infrared LEDs
Speaker Camera
Stand
Microphone
+ / VOL / -
Basic operation - Baby unit
Adjust speaker volume
Press + / VOL / - to adjust your baby unit speaker
volume. It determines the talkback volume
transmitted from your parent unit.
If you drill the holes into a stud, Align the wall mount bracket and Place the baby unit on the wall
go to step 3. screws with the holes in the wall mount bracket. Tighten the screw
as shown. Tighten the screw in the into the threaded socket at the
-OR-
middle hole first, so that the wall bottom to secure the baby unit.
If you drill the holes into an object
mount bracket position is fixed. You
other than a stud, insert the wall
can tighten the other screw in the
anchors into the holes. Tap gently
top hole.
on the ends with a hammer until
the wall anchors are flush with
the wall.
Change different views (require additional baby units - VM314)
You can view from different baby units if you have more than one baby units in your system
(VM314 purchased separately).
Speaker
Antenna
Temperature
sensor
Press VIEW to switch between the images of the baby units.
ON/OFF switch
ON/OFF light
Press PATROL to alternately view the image from the baby units every 10 seconds.
Turn off the baby unit
Slide the ON/OFF switch to the right to power
off your baby unit.
Press SPLIT to view the images from all baby units at once.
OR
Insert the screws into the Place the baby unit on the wall mount
holes and tighten the screws bracket. Tighten the screw into the threaded
until only 1/4 inch of the socket at the bottom to secure the baby
screws are exposed. unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Press VIEW
10s
The default angle of the wall mount bracket is 90 degrees. You
can maximize your baby unit's viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Specifications are subject to change without notice.
© 2016 VTech Communications, Inc. All rights reserved.
05/16. VM344_QSG_V6. Document order number: 96-010955-050-100