Advertisement
I
, O
NSTALLATION
Surface Mounted Lift
200 Cabel St., P.O. Box 3972, Louisville, KY 40206
IMPORTANT:
& M
PERATION
Two Post
M
Q10
ODEL
10,000
. C
LBS
APACITY
2500
.
A
LBS
PER
RM
QUALITY LIFTS, LLC
FAX: 502-583-5488
TOLL FREE: 877-771-5438
E-mail:
sales@qualitylifts.com
www.qualitylifts.com
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
M
AINTENANCE
ANUAL
Rev. 10/22/08
Advertisement
Table of Contents
Related Manuals for QUALITY LIFTS Q10
Summary of Contents for QUALITY LIFTS Q10
- Page 1 PERATION AINTENANCE ANUAL Two Post Surface Mounted Lift ODEL 10,000 APACITY 2500 QUALITY LIFTS, LLC 200 Cabel St., P.O. Box 3972, Louisville, KY 40206 FAX: 502-583-5488 TOLL FREE: 877-771-5438 E-mail: sales@qualitylifts.com www.qualitylifts.com IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE INSTALLING or OPERATING LIFT...
-
Page 2: General Specifications
Model Q10 Installation, Operation and Maintenance ENERAL PECIFICATIONS See Figure 1 Rise Height (Screw Pads Highest Position) 78 3/4" (2000mm) Overall Height (Adjustable) 147 1/2" (3748mm) / 137 1/2" (3494mm) Overall Width 131 3/4" (3347mm) Drive-Thru Clearance 98 3/8" (2499mm) Floor to Overhead Switch 140 1/2"... - Page 3 Model Q10 Installation, Operation and Maintenance Safety decals similar to those shown here are ERTICAL LEARANCE found on a properly installed lift. Be sure that all Check the height of the area where the lift is to safety decals have been correctly installed on the be installed.
- Page 4 Model Q10 Installation, Operation and Maintenance ECEIVING NSTALLATION The shipment should be thoroughly inspected as MPORTANT Always wear safety glasses while installing lift. soon as it is received. The signed bill of lading is OOLS MINIMUM REQUIRED acknowledgement by the carrier of receipt in a.
- Page 5 Model Q10 Installation, Operation and Maintenance YNCHRONIZER ABLES NCHORING 14) At upper beam sheave locations 4) The anchor bolts must be installed at least 8” disassemble and reassemble the cable from any crack, edge, or expansion joint. trapping rod to install the cable onto the 5) Use a concrete hammer drill with a 3/4 inch sheave, See Fig 3.
- Page 6 Model Q10 Installation, Operation and Maintenance & H OWER YDRAULIC INES 23) Route the remaining Power column hose beginning at the elbow fitting at the base up the backside of the column. Join the three hoses with the supplied union tee.
- Page 7 Model Q10 Installation, Operation and Maintenance LECTRICAL YNCHRONIZING ABLES 41) Raise lift and insure carriages lower into 29) Refer to Fig 8 Wiring Diagram for all steps same lock position. under this heading. Single Phase 42) Adjust synchronizing cables so the tension is...
-
Page 8: Wiring Diagram
Model Q10 Installation, Operation and Maintenance Wiring Diagram FOR SINGLE PHASE (Normally Open) FIELD CONECTIONS FOR THREE PHASE FACTORY WIRED FOR 208−240V RECONNECTIONS FOR 440−480V Fig 8 – Electrical Wiring Diagram Page 8 Rev. 10/22/08 Q10-IOM-Q .doc... -
Page 9: Operation Procedure
Model Q10 Installation, Operation and Maintenance The Owner/Employer shall display the lift PERATION ROCEDURE manufacturer’s operating instructions; ALI/SM AFETY OTICES AND ECALS 93 -1, ALI Lifting it Right safety manual; ALI/ST- 90 ALI Safety Tips card; ANSI/ALI ALOIM-2000, This product is furnished with graphic safety... - Page 10 RECOMMENDED LIFTING POINTS • Check adapters for damage or excessive wear. 3) Position the arms and adapters so all four Replace as required with genuine Quality Lifts pads contact the vehicle simultaneously. parts. The vehicle should remain level during lifting.
-
Page 11: Parts Breakdown
Model Q10 Installation, Operation and Maintenance Parts Breakdown Page 11 Rev. 10/22/08 Q10-IOM-Q .doc... - Page 12 Model Q10 Installation, Operation and Maintenance Page 12 Rev. 10/22/08 Q10-IOM-Q .doc...
- Page 13 JSJ5-03-07ch Cable Trapping Rod IMPORTANT Replace all worn or broken parts with genuine Quality Lifts parts. Contact your local Quality Lifts parts distributor for pricing and availability. Call Quality Lifts, Inc. at (502) 583-5438 for the distributor in your area.
Need help?
Do you have a question about the Q10 and is the answer not in the manual?
Questions and answers