Table of Contents
Advertisement
Quick Links
Installation, Operation & Maintenance Manual
Four Post
Surface Mounted Lift
Models Q4P09H, Q4P09X & Q4P09W
(9,000 lb Capacity)
200 Cabel Street, P.O. Box 3972, Louisville, Kentucky 40201-3972
Email:sales@qualitylifts.com
Web
site:www.qualitylifts.com
Office 877-771-5438/ 502-583-5438 Fax 502-583-5488
IMPORTANT:
READ THIS MANUAL COMPLETELY BEFORE
INSTALLING or OPERATING LIFT
Rev 12/26/2013
Advertisement
Table of Contents
Related Manuals for QUALITY LIFTS Q4P09H
Summary of Contents for QUALITY LIFTS Q4P09H
- Page 1 Installation, Operation & Maintenance Manual Four Post Surface Mounted Lift Models Q4P09H, Q4P09X & Q4P09W (9,000 lb Capacity) 200 Cabel Street, P.O. Box 3972, Louisville, Kentucky 40201-3972 Email:sales@qualitylifts.com site:www.qualitylifts.com Office 877-771-5438/ 502-583-5438 Fax 502-583-5488 IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE...
-
Page 2: General Specifications
Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance ENERAL PECIFICATIONS Q4P09H Q4P09X Q4P09W SPECIFICATIONS 209½” [17’-5½”] 233½” [19’-5½”] 233 ½” [19’-5½”] Length Overall 112¼” 112¼” 127¼” Width Overall 95” 95” 110” Inside Columns 160½” [13’-4½”] 184¾” [15’-4¾”] 184¾” [15’-4¾”] Between Columns 84½”... - Page 3 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance Fig 2 – Drive Under Height Rev 12/26/13 Q4P09-IOM-Q.doc...
-
Page 4: Vertical Clearance
Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance ERTICAL LEARANCE AFETY OTICES AND ECALS Check the height of the area where the lift is to be For your safety, and the safety of others, read and installed. Clearance should be calculated based on understand all of the safety notices and decals the full raised height of the lift. -
Page 5: Installation
IDLER COLUMN ASS’Y the shorted or damaged goods. Do this for your own protection. ENTRANCE RAMP NOTIFY Quality Lifts AT ONCE if any hidden loss CROSS BEAM ASS’Y or damage is discovered after receipt. POWER UNIT IT IS DIFFICULT TO COLLECT FOR LOSS OR... - Page 6 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance 4) Check the lock clevis to ensure it is secure and that the lock pawl is in the correct position as shown in Fig 4. Adjust the clevis if necessary. Fig 5 – Column/Cross Beam Assembly...
- Page 7 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance Fig 10 – Cable Layout Fig 8 – Hydraulic Ports 12) Remove the four (4) cross beam sheaves (one sheave from each end). The runway sheave pins do not need to be removed.
- Page 8 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance 20) Check the layout of the lift in the bay. anchoring the lift, this is the last chance to make adjustments. Adjust the position of the runways so the distance from power side...
- Page 9 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance 31) Assemble washer and nut to anchor with nut 35) Remove the 3/8-18 NPT plug on the side of just below impact section of bolt. Drive the power unit and attach the 90 degree anchor into hole until nut and washer contact elbow at a slightly downward angle.
- Page 10 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance NOTE: Whe n attaching the return line to t he OLUMN ECAL LACEMENT bulk head i n the run way, make sure it is securely attached at the power unit, and the...
-
Page 11: Operation Procedure
Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance FOR SINGLE PHASE (Normally Open) FIELD CONECTIONS Fig 24 – NON STANDARD 230V WIRING DIAGRAM Maintenance; and the employer shall insure that PERATION ROCEDURE the lift maintenance personnel are qualified and... -
Page 12: Lifting A Vehicle
Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance SAVE THESE INSTRUCTIONS IFTING A EHICLE AINTENANCE Place entrance ramps in the slotted holes on the To avoid personal injury, permit only qualified front of the ramp. Drive vehicle onto lift. Set the personnel to perform maintenance on this parking brake. -
Page 13: Optional Accessories
Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance PTIONAL CCESSORIES (Q4P09CS) OBILITY 1) This set of four casters when attached to the (Q4P09DT) cross beams of an unloaded lift, Fig 29, pick 1) Place drip tray between runways in the Jack the lift up and allow it to be rolled to a different rail, Fig 26. - Page 14 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance (Q4P09PR) IVOTING 1) Raise the lift to a comfortable working height 6) Assemble the ramp to the base with the ramp and set into the locks. hinge pin. Use the provided cotter pins to secure the pin in place, Fig 33.
- Page 15 IMPORTANT!!! Replace all worn or broken parts with genuine Quality Lifts Inc. parts. Contact your local Quality Lifts Parts Distributor for pricing and availability. (Call Quality Lifts Inc. (502) 583-5438 for the Parts Distributor in your area) Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 16 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance Parts Breakdown Fig A. General Layout Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 17 3/8-18 NPT x M14x1.5 90 DEGREE HYD. FITTING Replace all worn or broken parts with genuine Quality Lifts Inc. parts. Contact your local Quality Lifts Parts Distributor for pricing and availability. (Call Quality Lifts Inc. (502) 583-5438 for the Parts Distributor in your area) Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 18 M22x2.5 NUT Replace all worn or broken parts with genuine Quality Lifts Inc. parts. Contact your local Quality Lifts Parts Distributor for pricing and availability. (Call Quality Lifts Inc. (502) 583-5438 for the Parts Distributor in your area) Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 19 RUNWAY SHEAVE SPACER - SHORT Replace all worn or broken parts with genuine Quality Lifts Inc. parts. Contact your local Quality Lifts Parts Distributor for pricing and availability. (Call Quality Lifts Inc. (502) 583-5438 for the Parts Distributor in your area) Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 20 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance PARTS BREAKDOWN (continued) Fig D. Cross Beams Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 21 PRIMARY LOCK EXTENSION SPRING Replace all worn or broken parts with genuine Quality Lifts Inc. parts. Contact your local Quality Lifts Parts Distributor for pricing and availability. (Call Quality Lifts Inc. (502) 583-5438 for the Parts Distributor in your area) Rev 12/26/13 Q4P09-IOM-Q.doc...
- Page 22 Models Q4P09H, Q4P09X & Q4P09W Installation, Operation and Maintenance Caster Assembly ITEM # PART # QTY/ASSY DESCRIPTION TCS4-06-01-00A Caster Weldment TCS4-06-03 Caster Wheel X10-077 Bolt, M10 x 25mm Long X10-019 Nut, M10 X10-073 Washer, 10mm TCS4-06-02 Pivot Pin GJY12-3 Hairpin cotter...
-
Page 23: Warranty Registration Form
CITY: _________________________ STATE: _________ ZIP: ___________ Please remit form to: Quality Lifts P.O. Box 3972 Louisville, KY 40201 (877) 771-5438 office (502) 583-5488 fax This form must be received by Quality lifts for warranty to become effective.! Rev 12/26/13 Q4P09-IOM-Q.doc...