TP-Link TL-SG105E Installation Manual page 2

LED Explanation
1000M (Green)
On: Running at 1000Mbps
Flashing: Transmitting/receiving data
Power
On: Power on
Off: Power off
Frequently Asked Questions (FAQ)
Q1. The Power LED is not lit
The Power LED should be lit when the power system is working normally.
If the Power LED is not lit, please check as follows:
A1: Make sure the power adapter is connected to the switch with power
source properly.
A2: Make sure the voltage of the power supply meets the requirements of
the input voltage of the switch.
A3: Make sure the power source is ON.
Q2. The Link/Act LED is not lit when a device is connected to
the corresponding port
It is recommended that you check the following items:
A1: Make sure that the cable connectors are firmly plugged into the switch
and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
Environmental and Physical Specifications
Operating Temperature 0˚C~40˚C (32˚F~104˚F)
Storage Temperature -40˚C~70˚C (-40˚F~158˚F)
Operating Humidity 10%~90% non-condensing
Storage Humidity 5%~95% non-condensing
SAFETY NOTICES
Cautions
Do not use this product near water, for example,
in a wet basement or near a swimming pool.
Avoid using this product during an electrical
storm. There may be a remote risk of electric
shock from lightning.
COPYRIGHT & TRADEMARKS
Specifications are subject to change without
notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other
brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced
used to make
in any form or by any means or
any derivative such as translation,
10/100M (Yellow)
On: Running at 10/100Mbps
Flashing: Transmitting/receiving data
transformation, or adaptation without
permission from TP-LINK TECHNOLOGIES
CO., LTD. Copyright © 2016 TP-LINK
TECHNOLOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
CE Mark Warning
This is a class B product. In a domestic
environment, this product may cause radio
interference, in which case the user may be
required to take adequate measures.
General Specifications
Standard
IEEE802.3i, IEEE802.3u, IEEE802.3ab,
IEEE802.3x, IEEE802.1p, IEEE802.1q
Protocol
CSMA/CD
Ethernet: 10Mbps (Half Duplex)
Data Transfer Rate
Fast Ethernet: 100Mbps (Half Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
10Base-T:
UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100Base-TX:
Network Media (Cable)
UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
1000Base-T:
UTP category 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
Interface
5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports
LED indicators
Power, 10/100M LED, 1000M LED
Transfer Method
Store-and-Forward
MAC Address Learning
Automatically learning, automatically aging
10Base-T: 14881pps/Port
Frame Filter Rate
100Base-Tx: 148810pps/Port
1000Base-T: 1488095pps/Port
10Base-T: 14881pps/Port
Frame Forward Rate
100Base-Tx: 148810pps/Port
1000Base-T: 1488095pps/Port
FCC STATEMENT
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
20Mbps (Full Duplex)
200Mbps (Full Duplex)
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV
technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful
interference.
2) This device must accept any interference
received, including interference that may cause
undesired operation.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.