Elite Screens TE200HR2 User Manual

Elite Screens TE200HR2 User Manual

Cinetension plus series. electric motorized tab-tensioned rear projection screen

Advertisement

Quick Links

Electric Motorized Tab-Tensioned Rear Projection Screen
CineTension Plus Series
Important Safety & Warning Precautions
Make sure to read this user's guide and follow the procedures below.
Caution: The screen's Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty. For more information, please contact our Technical Support
Department at (877) 511-1211 Ext. 604.
Please retain this user's guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven or inclined surfaces.
Do not put heavy objects on the power cord and position it properly to avoid creating a trip
obstacle.
Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short
circuit.
There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.
No one except authorized technicians can open and make repairs to this unit.
Make sure the power source this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to
avoid overheat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
Avoid direct Sunshine, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Cut off the power supply first before transportation or maintenance.
Fully disconnect from the power supply when the unit is not in use for a long period of time, as
should be done with any other electric household appliance.
To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or if there are any evident broken parts.
Rev.053117 DR
User's Guide
1
www.elitescreens.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TE200HR2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Elite Screens TE200HR2

  • Page 1 Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your warranty.
  • Page 2 Please be aware of this as it will void the limitation of your warranty. Individual modifications to this product are prohibited and will void the warranty with the manufacturer. Please contact Elite Screens Customer Service for any questions. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 3 Installation Instructions Recessed Installation 1. Select the installation location for your screen. Measure the distances between each eye bolt (Shown as measurements L and A in Fig.1). Mark the installation area on the ceiling based on the measurements taken. Using the marks as a guideline, drill a hole in the ceiling for each suspension bolt. The distance between the installation hole (M) and the wall should be no longer than the measurement A.
  • Page 4 CineTension Plus Series | Controls and Accessories A. IR Remote B. RF Remote C. Wall switch control box D. 5-12 volt trigger cable E. IR extended “eye” receiver F. Wireless 5-12v trigger cable G. AAA batteries Screen operation Electric Current: Depending upon region, your Elite Screen will operate on 110v, or 220v voltage. 1.
  • Page 5 3 prong power cord 4. 5-12 volt trigger (Item D, Fig 4): The built-in 5- 12V trigger input allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers on and will retract when the projector powers off.
  • Page 6 Dimensions Table Model Number Unit: Inches 8.7- TE200HR2 204.0 197.2 192.0 174.3 196.0 112.3 98.1 105.6 11.2 Unit: mm 220- TE200HR2 5182 5009 4878 4428 4978 2853 2491 2683 Note: Data Error: ±1" For local EliteProAV contact or Technical Support, please visit www.eliteproav.com...

Table of Contents