Download Print this page

Electrolux T5290 Installation Manual

Type n2
Hide thumbs

Advertisement

Installation manual

Tumble dryer

T5290
Type N2...
438 9054-00/EN
Original instructions
2018.02.08

Advertisement

loading

  Also See for Electrolux T5290

  Summary of Contents for Electrolux T5290

  • Page 1: Tumble Dryer

    Installation manual Tumble dryer T5290 Type N2... 438 9054-00/EN Original instructions 2018.02.08...
  • Page 3: Table Of Contents

    Contents Contents 1 Safety Precautions ..........................5 General safety information......................7 Commercial use only........................7 Symbols............................7 2 Technical data.............................8 Drawing ............................8 Technical data ...........................9 Connections ..........................9 3 Setup ...............................10 Unpacking ..........................10 Siting ............................11 Mechanical installation ......................11 4 Marine installation ..........................12 5 Reversing the door ..........................13 6 Evacuation system ..........................16 Air principle ..........................16 Fresh air..........................17...
  • Page 5: Safety Precautions

    Installation manual 1 Safety Precautions • The machine is not to be used if industrial chemicals have been used for cleaning. • Do not dry unwashed items in the machine. • Items that have been soiled with substances such as cooking oil, ace- tone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the machine.
  • Page 6 Installation manual • When the power is disconnected, the operator must see that the ma- chine is disconnected (that the plug is removed and remains removed) from any point to which he has access. If this is not possible, due to the construction or installation of the machine, a disconnection with a locking system in the isolated position shall be provided.
  • Page 7: General Safety Information

    Installation manual with the appliance. Cleaning and user maintenance shall not be made by children without supervision. • Additional requirements for other countries: – This appliance is not intended for use by persons (including chil- dren) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given super- vision or instruction concerning use of the appliance by a person responsible for their safety.
  • Page 8: Technical Data

    Installation manual 2 Technical data 2.1 Drawing fig.7252 Operating panel Door opening, ⌀ 580 mm Electrical connection Gas connection Exhaust connection Steam: in Steam: out B(a) B(b) 1210 1358 1688...
  • Page 9: Technical Data

    Installation manual 2.2 Technical data Weight, net Drum volume litres Drum diameter Drum depth Drum speed, medium load Rated capacity, filling factor 1:18 (Max. load) 16.1 Rated capacity, filling factor 1:22 (Recommended. load) 13.2 Heating: Electricity 13.5 Heating: Gas Heating: Steam at 600–700 kPa Steam pressure 100–1000 Maximum air flow, Electric 50 Hz / 60 Hz...
  • Page 10: Setup

    Installation manual 3 Setup 3.1 Unpacking Note! Two persons are recommended for the unpacking. The machine is delivered complete with supporting feet. The machine is delivered bolted onto the transport pallet and packed in a crate or box. Remove packing from the machine. Remove the bolts between the machine and pallet.
  • Page 11: Siting

    Installation manual 3.2 Siting The machine should be positioned so that there is plenty of room for working, both for the user and service personnel. The figure shows minimum distance to a wall and/or other machines. Min. 20 mm / 13/16 inch fig.7187 3.3 Mechanical installation...
  • Page 12: Marine Installation

    Installation manual 4 Marine installation To ensure steadiness of the machine it is important to fasten the machine to the foundation. • Fasten the four clips (A), supplied with the machine, to the foundation. The clips shall be fastened with at least M10 bolts (B).
  • Page 13: Reversing The Door

    Installation manual 5 Reversing the door Disconnect the power to the machine. Demount the hinges and remove the door. Remove the upper hinge first. fig.7166 Remove the screws on the front panel and carefully loosen the panel. Push the door switch cable down through the hole in order to access the cable and then disconnect the cable.
  • Page 14 Installation manual Loosen the nuts and move the two brackets to the opposite side. fig.7171 Move the door switch on the front panel. fig.7172...
  • Page 15 Installation manual Move the four metal clips from the opposite side. fig.7174 Connect the door switch cable and push the cable in over the drum and pull it upwards. fig.7549 Remount the front panel. Ensure that the door switch cable does not get damaged when remounting the front panel. Fasten the hinges and mount the door on the opposite side.
  • Page 16: Evacuation System

    Installation manual 6 Evacuation system 6.1 Air principle The fan creates low pressure in the machine, drawing air into the drum via the heating unit. The heated air passes through the garments and the drum holes. The air then flows out through a lint filter positioned below the drum. Then the air is evacuated through the fan and exhaust system.
  • Page 17: Fresh Air

    Installation manual 6.2 Fresh air For maximum efficiency and the shortest possible drying time, it is important to ensure that fresh air is able to enter the room from the outside in the same volume as that blown out of the room. To avoid draught in the room it is important to place the air inlet behind the machine.
  • Page 18: Shared Exhaust Duct

    Installation manual 6.4 Shared exhaust duct It is recommended that each machine is connected to a separate exhaust duct. When several machines shall use the same exhaust duct the exhaust duct must increase after each machine. Number of machines ⌀ mm Exhaust duct Recommended area 0.16...
  • Page 19: Adjusting The Dryer

    Model name Heating / Frequency Static pressure in Resulting Nominal air flow cold empty ma- NTC sensor position chine (m (Pa) T5290 Electric / 50 Hz T5290 Electric / 60 Hz T5290 Gas / 50 Hz T5290 Gas / 60 Hz...
  • Page 20 Installation manual Alternative measuring meathod Adjusting the air flow may only be carried out by authorized personnel. Use a home made U tube manometer, a hose (max ⌀ 10 mm), with water. Insert one end of the hose in the hole, hold the hose according to the picture so that the water is in level.
  • Page 21: Steam Connection

    Installation manual 7 Steam connection 7.1 Connecting the steam Note! The steam supply must be cut off and must not be under pressure. • The branch pipe’s must be located at the top of the main steam pipe to prevent condensation in the steam. •...
  • Page 22: Steam Calorifier

    Installation manual 7.2 Steam calorifier Mount the steam calorifier Unpack the steam calorifier. Demount the back panel on the machine. Demount the supporting rail on the machine (A). Note which way the supporting rail turns as it has to be remounted the same way.
  • Page 23: Gas Connection

    Installation manual 8 Gas connection 8.1 Fasten the label Before installing the machine fasten the label “Read the user instructions” on the inside of the door in a suitable place and at the front panel. The label must have the correct country code, choose the correct label from the gas kit. fig.7113 8.2 General May only be carried out by qualified personnel.
  • Page 24: Gas Installation

    Installation manual 8.3 Gas installation This gas appliance is build to run on natural gas (group I2H and I2E), commonly identified by GNH. Japan to run on LPG (group I3B/P) 2800 Pa inlet pressure, no regulation. The data label shows the injector size and the injector pressure and the countries that use this gas quality: Albania Iceland Austria...
  • Page 25: Table Of Pressure And Adjustment

    Installation manual 8.4 Table of pressure and adjustment Liquid petrole- Gas category Inlet pressure Injector pres- Injector size (⌀ Air reducing Label number May be avail- um gases (mbar) sure (mbar) plate (mm) able in follow- ing countries Butane mixture 28-30 / No regulation 2.30...
  • Page 26: Test Run

    Installation manual 8.5 Test run • Loosen the measuring branch screw (2) 1/4 turn; connect a manometer to the measuring branch. • Select a program with heat. • Start the machine. • Check the nozzle pressure, see “Table of pressure and adjustment”. •...
  • Page 27: Data Label

    Installation manual • Loosen the measuring branch screw (2) 1/4 turn; connect a manometer to the measuring branch. • Connect the power to the machine and select a program with heat. • Start the machine. • Set the correct nozzle pressure according to the table on setting screw (4) under the cover screw (3). fig.7120 •...
  • Page 28: Electrical Connection

    Installation manual 9 Electrical connection 9.1 Electrical installation The electrical installation may only be carried out by qualified personnel. Machines with frequency-controlled motors can be incompatible with certain types of earth leakage circuit break- er. It is important to know that the machines are designed to provide a high level of personal safety, which is why items of external equipment such as earth leakage circuit breakers are not necessary.
  • Page 29: Three-Phase Connection

    Installation manual 9.3 Three-phase connection Demount the cover panel from the supply unit. Connect the earth and other wires as shown. 3NAC 3NAC When the installation is completed remount the cover panel and check: • That the drum is empty. •...
  • Page 30: Functions For I/O-Cards

    Installation manual 9.5 Functions for I/O-cards The electrical schematic can be one of the following: 9.5.1 Central payment (2J) To start the machine from a central payment system, the payment system must transmit a start pulse 300–3000 ms (500 ms is recommended) with a minimum pause of 300 ms (500 ms is recommended) between two pulses. The start pulse can be either 230V or 24V.
  • Page 31: Central Payment (2J)

    Installation manual 9.5.2 Central payment (2J) The central payment or booking system shall transmit an active (high) signal to the machine once permission has been granted to start the machine. The signal must remain active (high) during drying. When the signal gets inactive (low) the machine will abort ongoing program and enter cooling.
  • Page 32: External Coin Meter/Central Payment (2K)

    Installation manual 9.5.3 External coin meter/Central payment (2K) The signal received from external coin meters must be a pulse between 300–3000 ms (500 ms is recommended) with a minimum pause of 300 ms (500 ms is recommended) between two pulses. fig.7438...
  • Page 33: Price Reduction (2K)

    Installation manual 9.5.4 Price reduction (2K) By maintaining an activated (high) signal on connection 5 ("Price red"), the price of the program can be reduced. This function has a number of uses, including providing reductions during a specific period of the day. Whilst the signal re- mains active (high), the price of the program is reduced (or the time is increased on time programs), by the percent- age entered in the price programming menu.
  • Page 34: At First Power Up

    Installation manual 10 At first power up When the installation is complete and the power is connected for the first time you will be forced to make the following settings. When one setting is ready you will automatically enter the next one. •...
  • Page 35: Function Check

    Installation manual 11 Function check May only be carried out by qualified personnel. A function check must be made when the installation is finished and before the machine can be ready to be used. Whenever a repair has been made, a function check must be performed before the machine can be used again. Check the automatic stop of the machine •...
  • Page 36 Installation manual Ready to use If all tests are OK the machine is now ready to be used. If some of the tests failed, or deficiencies or errors are detected, please contact your local service organisation or dealer. The installer shall instruct the user on the operation of the appliance before leaving.
  • Page 40 Electrolux Laundry Systems Sweden AB 341 80 Ljungby, Sweden www.electrolux.com/professional Share more of our thinking at www.electrolux.com...