Table of Contents
Advertisement
SPECIFIC SAFETY RULES FOR TRIMMER USE
Make sure all guards, straps, deflectors and handles are
properly and securely attached.
Use only the manufacturer's replacement line in the
cutting head. Do not use any other cutting attachment.
Never operate unit without the safety guard in place
and in good condition.
Maintain a firm grip on both handles while trimming. Keep
bump head below waist level. Never cut with the bump
head located over 76 cm (30 in.) or more above the
ground.
SPECIFICATION
Weight
Without fuel and string head
Without fuel with string head
Fuel tank volume
Cutting swath
Engine displacement
Maximum engine performance
(in accordance with ISO 8893)
Maximum rotational frequency of the the spindle
Engine speed (rotational frequency) at
recommended max. spindle rtational frequency
Engine speed (rotational frequency) at idle
Fuel consumption (in accordance with ISO 8893)
at max. engine performance
Specific fuel consumption (in accordance with ISO 8893)
at max. engine performance
Vibration level idling
Front handle
Rear handle
Vibration level racing
Front handle
Rear handle
Sound pressure level (in accordance with
EN ISO 11806:1997, ISO 7917:1987)
Sound power level (in accordance with ISO 10884)
DESCRIPTION
1.
Starter Grip
2.
Front Handle
3.
Shaft
4.
Throttle Trigger
5.
Safety Guard
6.
Cutting Line
7.
Bump Head
8.
On / Off Switch
9.
Throttle Control &
Rear Handle
Throttle Interlock
10.
11.
Choke Lever
12.
Bolt
13.
Bracket
14.
Wing Nut
15.
Lock W asher
4.48 Kg
16.
Flat W asher
4.67 Kg
17.
Muffler Guard
3
425 cm
18.
Rear Housing
432 mm
19.
Idle Speed Screw
30 cc
20.
Bent End Of MufflerGuard
21.
Opening In Rear Housing
0.78 kW
22.
Latch
-1
9000 min
23.
Dangerous CuttingArea
24.
Best Cutting Area
12500 min
-1
25.
Direction Of Rotation
-1
3100 - 4300 min
26.
"L" Lo Needle
27.
Primer Bulb
0.52 kg/h
0.47 kg/h
ASSEMBLY
4.8 m/s
2
AT TACHING THE POWER HEAD TO THE TRIMMER
4.3 m/s
2
ATTACHMENT
WARNING
2
7.1 m/s
Never attach or adjust any attachment while
9.0 m/s
2
power head is running. Failure to stop the engine
may cause serious personal injury.
100dBA
The trimmer attachment (50) connects to the power head
110dBpA
by means of a coupler (51) device.
Loosen the knob (52) on the coupler of the power
head shaft (53) and remove the end cap from the
attachment.
Push in the button (54) located on the trimmer attachment
shaft. Align the button with the guide recess (55) on
the power head coupler and slide the two shafts together
Rotate the trimmer attachment shaft until the button
locks into the positioning hole (56).
- 3 -
28.
To rx Wrench
29.
Run Position
30.
Half Choke Position
31.
FullChoke Position
32.
Bump Knob
33.
Slots
34.
Eyelets
35.
Drive Connector
36.
Spring
37.
FirstLine
38.
Anchor Hole
39.
Arrows On Spool
40.
Second Line
41.
Tabs
42.
Cover
43.
Filter
44.
Air Filter Cover
"H" High Needle
45.
46.
Inner Spool
47.
Screws
48.
Fuel Cap
49.
Cut Off Blade
50.
Trimmer Attachment
51.
Coupler
52.
Knob
53.
Power Head Shaft
54.
Button
55.
Guide Recess
56.
Positioning hole
.
Hide quick links:
Advertisement
Table of Contents
