Related Manuals for PORTMAN GST8000
Summary of Contents for PORTMAN GST8000
- Page 1 Portman Security Systems, Ltd Operation Manual GPRS / GPS TRACKING SYSTEM Model: GST8000 Version 2.0...
- Page 2 1.2 Report Setup GST8000 must be initialized by PORTMAN PC setup program in order to make communication with the remote server /call center. There are 9 main sections that allow users to program the device, (1) User detail (Device ID, server IP, and port, SMS number, GPRS APN…) (2) In-built Geofence definition (up to 1 self geofence, 4 circular geofence,...
- Page 3 setting (Time, Distance, Intelligent mode, Temperature, Low battery, Course change…) (4) Roam report setting (Time, Distance, Intelligent mode, Temperature, Low battery, Course change…) local or send or ignore. (5) Alarm setup (to enable or disable the event generated by the inputs or external alarm, e.g. ignition, DOOR, ALARM...) (6) Roam Alarm setup (to enable or disable the event generated by the inputs or external alarm, e.g.
- Page 4 User can deactivate the self-Geofence at any time by pressing the button again. If the GPS cannot be located when the Immediate Geofence function is been executed, GST8000 will used the last known position as the origin of the circular Geofence zone to perform the protection.
- Page 5 For long periods of inactivity user have the options to set the unit in sleep mode this will enable the unit to save electric power. GST8000 Can go to sleep mode when ignition goes off, TL-sensor not be trigger for 5minuts and this feature is configurable. “GPS” can be power off. User can setup the automatically wakeup time during the sleep mode to ensure the device is working.
- Page 6 AD1 input AD2 input 1. Door Lock 3 output 2. Door Unlock 3. Coil (for E-card searching) GPS port will output NMEA 0183 GPS data. GPS output interface Data rate: 9600 bps Valet Switch (1) Send help report (2) activate or deactivate Immediate Geofence Initialize the unit and program the device, including Network APN, server IP address, user message, report control, and Geogence PC-setup...
-
Page 7: Status Indicator
(3)ID CARD learn mode: Turn ignition ON, press Valet Switch 12 times within 10 sec, the valet LED will keep on for 1 second to enter ID card learning mode, the new ID CARD can be learn in this time. If no ID card can be learn during 10 seconds, unit will exit ID card learning mode. - Page 8 Select the correct COM port number, then “reset” the unit by pressing the reset button, and next click “OK”. Note that: it is necessary to power on and reset the PORTMAN device soon after click the “ok” button. PC setup program will detect the hardware for 60 seconds. If no hardware is detected, it will exit.
- Page 9 C. MAIN INTERFACE 1. [User detail:] If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. Set UNIT ID and UNIT password of for the device. Note: Device ID length does not more than 4-characters, otherwise SBD compressed packet will more than 30 bytes, and communication data fee is double.
- Page 10 Set Access Point Name (APN), User Name, Password. The maximum length of the APN, User name and Password is 49 characters. TCP/UDP address and Port number of the remote server being set, UNIT will send report to these address. Note that only one TCP or UDP server will be used at the same time. To select enable or disable local GPRS/SMS or Roam GPRS/SMS Set the SMS Number of the user.
- Page 11 If “ID card control start kill enable” was selected, the unit will disarm by ID-card only or emergency release. “Initialize ” button: clear all data in UNIT. Request All: read out the whole existing setting from GST8000. Request: read out the setting in the current page. Apply: transfer the setting to GST8000 in the current pages.
- Page 12 in order to make the connection. If the report sending using GPRS connection fails, the report will be sent to the ‘primary’ SMS number first. The report will be resent, when the GPRS connection becomes available. 2. [Geofence:] Four Circular Geofence and one self-geofence: Circular Geofence must set origin and radius: Origin format :N2446.5321E12120.4231;...
- Page 13 N2446.5321 is latitude, E12120.4231 is longitude. Radius from 0.1 km to 1000km. User can set the reports send or local or ignore: Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports.
- Page 14 20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated.
- Page 15 3. [Report:] Automatic report can be configured in this section. To activate the function(s), please select “√” in checkbox and fill in data in the textbox. The reports will be summarized as (1) Local Intelligent report...
- Page 16 Parameters: report time when moving, report time when stop, threshold speed, send stop report after a preset value and to choose the reports send or ignore. Report when speed less than a preset value (refer the following 1.5 Km/Hr), and it will send stop report after the preset time (refer the following 120Sec).
- Page 17 (4) A/D 2 detect report [on/off] SEND REPORT IF ADC2 LESS THAN [min voltage] V for [debounce time] SEC, RESEND PER [resend time] SEC [on/off] SEND REPORT IF ADC2 MORE THAN [max voltage] V for [debounce time] SEC, RESEND PER [resend time] SEC [on/off] SEND REPORT IF ADC2 GO UP [up voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC2 GO DOWN [down voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC2 ENTER/EXIT [min voltage] V TO [max voltage] V for...
- Page 18 speed is 110Km/h and exit over speed delay time is 2 sec. If vehicle speed over threshold speed 20seconds, system will send speed over report once interval 20 sec until exit speed over delay time 2 sec, the over speed report will stop to send. If alert when over speed has configured, then it will alert when speed over.
- Page 19 (8) Towaway report When system in ignition OFF mode, if the vehicle has been towed away, unit will sent a towaway report. (9) Course change report (to send a report when the course change is bigger than the value set here) Parameters: Course change in degree and report send or ignore (10) Fixed report...
- Page 20 If there is trigger report, the unit will connect to server immediately. Special command for SMS mode: If the GST8000 is not in the GPRS online status, user can send command &&Y02 or &&Y04 to ask unit to connect to server. This command can be sent from any device via SMS;...
- Page 21 4. [Roam alarm] All the roam reports configured are same as Local report. Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports.
- Page 22 Also build in car alarm function can be set on here. Sleep mode (when ignition OFF) (1) GST8000 can go to sleep mode when ignition goes off and TL-sensor not be trigger for 5minuts. In sleep mode, GPS will be disabled.
- Page 23 (3) If any of the inputs are triggered while in the sleep mode, the system will wake up automatic and then send reports to the server. The input triggers for waking the device up are selectable. If the GPRS connection is failed, for emergency purpose, GST8000 will send out SMS report if number is defined.
- Page 24 6. [Roam alarm] All the roam alarm configured are same as Local report. Send: report will send out immediately if generation Local: report will save if generation, it will send out by local network Ignore: cancel reports.
- Page 25 7. [GSM roaming] 1) Roaming GPRS mode...
- Page 26 Use can configure roaming GPRS mode with automatic register or manual register in this field. When roaming GPRS mode in manual register, user can set 20 prefer operators, main unit will search and register from the 20 prefer operators. 2) Compress setting To send report in local GPRS, compressing N reports to a packet and then send out.(N: the digit between 1~8) To send report in roam GPRS, compressing N reports to a packet and then send...
- Page 27 8. [SBD setting] IMEI: Any operate with ‘request or request all’ after GPRS power on, the module series number will display automatically, otherwise it displayed with space. This report is special for satellite module. It is different to intelligent report defined in common report setting.
- Page 28 This report is special for satellite module. It is different to fix time report defined in common report setting. This report only work when no GSM coverage. Attention: because consumption with satellite is different to GPRS/SMS. Pay attention to report frequency. This report is special for satellite module.
- Page 29 9. ID card ID card learning function: Press ‘scan’ and put the ID card near coil The unit will read ID card number and display in here Press ‘add’ once Press ‘APPLY’ to save the ID card number to unit. Up to 20 ID numbers can be saved when the ID list was set here, if unit didn’t detect valid ID or invalid ID was detected, the ignition won’t be started, if the ID list was not set, then user can start the ignition without...
- Page 30 GST8000 SPECIFICATIONS Physical Parameters Enclosure dimensions 160(L)*115(W)*70(H) Weight 1000g Electrical DC Supply voltage DC Tolerance voltage 9V－16V Current (GPRS online) 45mA Current (GPRS transmission) 100mA Current (GPRS Peak) 140mA Current (Sleep) 25mA (GPS and Satellite module are off) Current (SBD standby)
-
Page 31: Packing List
Position accuracy (Horizontal) ＜2.5m CEP autonomous ＜2.0m CEP SBAX Time to first fix Hot start 1 ＜1s Warm start 2 ＜32s Cold 3 ＜35s Standard GPS software NMEA message switchable GGA, GSA GSV, VTG, RMC, GLL Satellite module DC supply voltage Baud Rate 19200 Frequency range... - Page 34 Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
Need help?
Do you have a question about the GST8000 and is the answer not in the manual?
Questions and answers