Advertisement
Quick Links
Advertisement
Related Manuals for PORTMAN GT3100
Summary of Contents for PORTMAN GT3100
- Page 1 GPS&GPRS TRACKING SYSTEM GT3100 OPERATION/INSTALLER MANUAL...
- Page 2 1.2 Report Setup GT3100 must be initialized by PORTMAN PC setup program in order to make communication with the remote server /call center. There are four main sections that allow users to program the device, (1) User detail (Device ID, server IP, and port, SMS number, GPRS APN…) (2) In-built Geo-fence definition (up to 5 circular, 5...
- Page 3 User can deactivate the self-Geo-fence at any time by pressing the valet switch again. If the GPS cannot be located when the Immediate Geo-fence function is been executed, GT3100 will use the last known position as the origin of the circular Geo-fence zone to perform the protection.
- Page 4 1.7 Valet switch operation User can use the supplied Valet switch to perform 5 essential tasks, including (1) sending help report (2) activate or deactivate Immediate Geo-fence (3) sending ‘Duty on’ or ‘Duty off’ report to the server (4) Emergency release to exit ‘ARM’, ‘Anti-carjacking’ or ‘Panic’ modes (1) Sending ‘HELP’...
- Page 5 II. BASIC FUNCTIONS FUNCTIONS APPLICATIONS GPS receiver will output a complete position, velocity, and time (PVT) solution in the NMEA Version 3.0 protocol GPRS use standard TCP or UDP communicate protocol. If the GPRS service is failed, the GPRS, SMS SMS mode will be turned on for emergency use.
- Page 6 III. PANEL INSTALLATION AND WIRING DIAGRAM Horn Siren output output Siren/Horn output I/O Power Reset Valet select Jumper Port Output Switch Switch Temperature PC SETUP Sensor Antenna Antenna GPRS/GPS/POWER STATUS LED SIM CARD 1.) In-vehicle I/O and power port: for in-vehicle I/O, and power, etc …. 2.) GPS output port: white 2-pin connector.
-
Page 7: Status Indicator
Select the correct COM port number, then “reset” the unit by pressing the reset button, and next click “OK”. Note that: it is necessary to power on and reset the PORTMAN device soon after click the “ok” button. PC setup program will detect the hardware for 60 seconds. If no hardware is detected, it will exit. - Page 8 C. MAIN INTERFACE 1. [User detail:] If the SIM card is password protected, user can input the “SIM PIN” window to set password of SIM Card. Set UNIT ID for the device.
- Page 9 UNIT can save 900 reports (900-1) recently; Click ‘Export’ button can export them with Excel or Text format. “Initialize ” button: clear all data in UNIT. Request All: read out the whole existing setting from GT3100. Request: read out the setting in the current page.
- Page 10 2. [Geo-fence:] 4 circular, 5 rectangle and 20 point Geo-fence areas can be set. When UNIT is out of these predefined zones, a report will be generated. When self Geo-fence is activated, It will record the current position as the origin and use the predefined distance for the radius to enable a circular Geo-fence.
- Page 11 The reports will be summarized as (1) Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed. (min. speed is 0.1 km/Hr, max. speed is 1000 km/Hr). (2) Intelligent history report (record the report in the system’s flash ram) Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed.
- Page 12 Special command for SMS mode: If the GT3100 is not in the GPRS online status, user can send command &&Y02 or &&Y04 to ask unit to connect to server. This command can be sent from any device via SMS;...
- Page 13 APPENDIX GT3100 SPECIFICATIONS Physical Parameters Enclosure dimensions 88(L)*76(W)*25(H) Weight 100g Electrical DC Supply voltage DC Tolerance voltage 9V－16V Current (GPRS online) 60mA Current (GPRS transmission) 80mA Current (Peak) 120mA GPRS* Frequency Range (MHz) Support 4-frequency 850/900/1800/1900 Channel spacing (Hz) GPRS connectivity...
- Page 14 1. Built in 20mA/H Ni-Mh 4.8V backup battery (optional) 2. Combined Antenna (with GPRS and active GPS) 900/1800 and 850/1900 MHz two types (optional) 3. GPS Active Antenna (optional) 4. Siren (optional) 5. Temperature sensor (optional) 6. PORTMAN PC-setup Cable (optional)
- Page 16 VI. Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
Need help?
Do you have a question about the GT3100 and is the answer not in the manual?
Questions and answers