Table of Contents
Advertisement
BT900-US Hardware Integration Guide
Intelligent BTv4.0 Dual Mode Module
Categories
Categories
Categories
Categories
Control Protocols
Control Protocols
Control Protocols
Control Protocols
FW upgrade
FW upgrade
FW upgrade
FW upgrade
Coexistence
Coexistence
Coexistence
Coexistence
Operating Modes
Operating Modes
Operating Modes
Operating Modes
Supply Voltage
Supply Voltage
Supply Voltage
Supply Voltage
Power
Power
Power
Power
Consumption
Consumption
Consumption
Consumption
Physical
Physical
Physical
Physical
Environmental
Environmental
Environmental
Environmental
Miscellaneous
Miscellaneous
Miscellaneous
Miscellaneous
Development Tools
Development Tools
Development Tools
Development Tools
Software Tools
Software Tools
Software Tools
Software Tools
Approvals
Approvals
Approvals
Approvals
Note 1: 1: 1: 1: DSR, DTR, RI, and DCD can be implemented in the
Note
Note
Note
Note
Note 2: 2: 2: 2: With I2C interface selected, pull-up resistors on I2C SDA and I2C SCL MUST be connected
Note
Note
externally as per I2C standard.
Note 3 3 3 3 : : : : SPI interface consists of SPI MOSI, SPI MISO and SPI CLK. SPI CS is created by customer using any
Note
Note
Note
spare SIO pin within their
Note 4: 4: 4: 4: BT900 module comes loaded with
Note
Note
Note
smart
with any
Laird provides many sample
Note 5 5 5 5 : : : : Deep sleep consumes 233uA of power when the BT900 internal radio chip 32.768kHz is used. The
Note
Note
Note
smart
BASIC runtime engine firmware (v9.1.2.0) has SIO (DIO default function) input pins that are
PULL-UP enabled by default. You may disable the internal PULL_UP through a
Embedded Wireless Solutions Support
Embedded Wireless Solutions Support
Embedded Wireless Solutions Support
Embedded Wireless Solutions Support
Center: http://ews
Center:
http://ews- - - - support.lairdtech.com
support.lairdtech.com
Center:
Center:
http://ews
http://ews
support.lairdtech.com
support.lairdtech.com
www.lairdtech.com/bluetooth
Feature
Feature
Feature
Feature
smart
BASIC runtime engine
FW upgrade
802.11 (Wi-Fi)
Self-contained Run Mode
Interactive Development
Mode
Supply
Current
User Configurable
Clocking
Dimensions
Operating
Storage
Lead Free
Warranty
Development Kit
Utilities
Bluetooth®
FCC / IC / CE / MIC
smart
BASIC application script allowing multi-dropping.
smart
BASIC application script (as that is dependent on customer end application or use).
smart
BASIC applications covering the services listed.
Implementation
Implementation
Implementation
Implementation
Any that can be implemented using
vSP – Virtual Serial Port for BLE – Command Mode
Only
Via UART
3 wire CSR schemes supported
(Unity-3 for classic BT, Unity-3e for BLE)
Selected by nAutoRUN pin status:
LOW (0V). Then runs $autorun$ (
application) if it exists.
HIGH (VCC). Then runs via at+run (and "file name" of
smart
BASIC application script).
Nominal 5VDC
Max Peak Current (TX Power @ +8 dBm TX): 85 mA
Standby Doze (waitevent) – 2.7mA (at 4MHz clock)
(Note
5)
Deep Sleep – 233 uA (external signal wakeup) See
Note 5
User configurable clocking (40MHz, 20MHz, 4MHz),
so user can reduce current consumption further.
50.7mm x 18.5mm x 10.4mm
-40°C to +85°C
-40°C to +85°C
Lead-free and RoHS compliant
One Year
Development board and free software tools
Windows, Android and iOS applications
UART Firmware Upgrade
Complete Declaration ID
All BT900 Series
smart
BASIC application.
BASIC runtime engine FW, but does not come loaded
smart
BASIC
smart
BASIC
smart
BASIC
Laird Technologies
Americas: +1-800-492-2320
Europe: +44-1628-858-940
Hong Kong: +852 2923 0610
Advertisement
Table of Contents
