Table of Contents
Advertisement
User Manual
600 Ceramic Cooktop Touch
AUPL-VCR4T
IMPORTANT
Please ensure that you read through this manual prior to installation and use. This user
manual contains important information to ensure optimal performance and keep you safe.
Please retain your proof of purchase, as this will be needed in the event that you require a
warranty service. Remember to keep this user manual for future reference.
| platinumappliances.com.au
Advertisement
Table of Contents
Related Manuals for Platinum AUPL-VCR4T
Summary of Contents for Platinum AUPL-VCR4T
- Page 1 User Manual 600 Ceramic Cooktop Touch AUPL-VCR4T IMPORTANT Please ensure that you read through this manual prior to installation and use. This user manual contains important information to ensure optimal performance and keep you safe. Please retain your proof of purchase, as this will be needed in the event that you require a warranty service.
-
Page 2: Table Of Contents
Contents Contents Warning & Safety Instructions Product Overview Electrical Connection Installation Operating Instructions Maintenance Your Cookware Product Specifications Contact Details Back Cover Page 2 600 Ceramic Hob Touch User Manual... -
Page 3: Warning & Safety Instructions
Warning & Safety Information CAUTION: Your safety is important to us. Please read this information before using your cooktop. INSTALLATION • This appliance is to be properly installed and earthed only by a suitably qualified ELECTRIC SHOCK HAZARD person. • Disconnect the appliance from the mains •... - Page 4 Warning & Safety Information HOT SURFACE HAZARD • After use, always turn off the cooking zones • Do not let your body, clothing or any item and the cooktop as described in this manual other than suitable cookware contact the (i.e.
-
Page 5: Product Overview
Product Overview 600 Ceramic Hob Touch User Manual Page 5... -
Page 6: Electrical Connection
Electrical Connection CONNECTING THE HOB TO THE MAINS POWER SUPPLY IMPORTANT: The power supply should be connected in compliance with the relevant standard, or a single-pole circuit breaker. The method of connection is shown below: 1. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools, so as to avoid any accidents. -
Page 7: Installation
Installation For the purpose of installation and use, a minimum 5 mm space shall be preserved around the hole. Be sure the thickness of the table surface is at least 30mm. Ensure that the benchtop material is heat-resistant to avoid deformation caused by the heat radiation from the hotplate. As shown in Figure (1) Under any circumstances, make sure the ceramic cooker hob is well ventilated and the air inlet and outlet are not blocked. - Page 8 Installation NOTICE: Adjust the bracket positionto suit for different work surface’s thickness. CAUTION: • The ceramic cooker hob must be installed by qualified personnel or technicians. Please never conduct the operation by yourself. • The ceramic cooker hob shall not bemounted to cooling equipment, dishwashers and rotary dryers.
-
Page 9: Operating Instructions
Operating Instructions MINUTE REMINDER To set a minute reminder, press “+” or “-” on the timer menu. The timer indicator will flash “00”, then adjust length of time by pressing “+” or “-” on the timer menu. When the time is set, the timer indicator will stop flashing after 5 seconds and countdown will start. -
Page 10: Maintenance
Maintenance Page 10 600 Ceramic Hob Touch User Manual... -
Page 11: Your Cookware
Your Cookware CHOOSING THE RIGHT COOKWARE Do not use cookware with jagged edges or a curved Always lift pans off the ceramic base. hob - do not slide, or they may scratch the glass. Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. -
Page 12: Contact Details
NSW 1755 1300 985 815 customercare@platinumappliances.com.au platinumappliances.com.au Platinum is committed to ongoing research and development. Every effort has been made to ensure all information in this user manual is correct at time of going to print. Dimensions should only be used as reference only and actual dimensions should be taken from the physical product only.