LG 22LG3DDH Owner's Manual page 104

The Express Script Installer Menu Wizard guides you through the process of setting up the essential items for
most hospital TV viewing applications and is displayed each time the TV is turned ON, unless it previously has
been completed or exited.
Note: If previously completed or exited, the Express Script Installer Menu Wizard also can be re-activated
from the Installer Menu—set Installer Menu item 117 FACT DEFAULT to 001 to initiate the Express Script
Installer Menu Wizard. See the "Installer Menu" section of this document for further information.
Note: If you plan to create a customized Master TV Setup using the procedure on pages 11 to 14, transfer
(Teach) a Master TV Setup to a Target TV, or configure a TV with an FTG device for FTG Mode of operation,
be sure to exit the Express Script in order to avoid setup conflicts that may cause the TV to malfunction.
Installer Menu Wizard
Select Menu Mode
Which menu mode will you be using?
Express Script
Exit Express Script
PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
Installer Menu Wizard
Step 1. Tuning Band
Which tuning band would you like to use?
Cable Standard
Exit Script
F G
Back
PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
Installer Menu Wizard
Step 2. Aux Input
Which inputs will you be using?
Customize Inputs.
Use default values.
Back
PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
Installer Menu Wizard
Step 3. Pillow Speaker
Up/Down/Left/Right arrow keys
Which brand pillow speaker code will you be using?
Zenith code
Exit Script
F G
Back
PTC: V0.00.007 CPU: V03.30.00 ASIC: 20E7
206-4190
1. Upon launching, the Express Script Installer Menu Wizard prompts you
to select a menu mode. Use the Up/Down arrow keys on the Installer
Remote to select the appropriate option:
• Select/highlight Express Script in order to proceed with the Installer
• Select/highlight Exit Express Script to exit the Installer Menu Wizard.
The remaining steps of this procedure describe the Express Script
OK
Installer Menu Wizard. Use the Installer Remote to make selections and
complete each step. You can select the Back button, where available, to
1 ► ► ► ► ► ►
2 3 4 5 6 7
check previous settings, as necessary.
►
2. Use the Left/Right arrow keys to select the appropriate tuning band
Next
(Cable Standard [default], Cable HRC, Cable IRC, or Air). When you have
made your selection, use the arrow keys to select Next, and then press
OK Exit Express Script
OK (Enter).
► ► ► ► ► ►
1 2 3 4 5 6 7 3. Use the Up/Down arrow keys to select the desired Aux input option.
(Note: If you simply select Next and press OK (Enter) in this step, default
values will be used.)
• To customize settings, select Customize Inputs and press OK (Enter).
Next
OK Exit Express Script
• To use default values, select Use default values and press OK (Enter).
1 ► ► 3 ► 4 ► 5 ► 6 ► 7
2
4. If using the Zenith pillow speaker code (default), you can simply select
Next and press OK (Enter).
► Otherwise, select the pillow speaker code field, and use the Left/Right
arrow keys to select the appropriate option. When you have made your
selection, use the arrow keys to select Next, and then press OK (Enter).
Next
OK Exit Express Script
Express Script Installer Menu Wizard
Menu Wizard. Then, press OK (Enter) on the Installer Remote.
Then, press OK (Enter) on the Installer Remote.
Caution: If you opt to exit the Express Script Installer Menu
Wizard at any time while it is in progress, any settings made
will not be retained.
Aux input options are displayed in a pop-up window. Use the arrow
keys to select the input(s) you want to enable or disable. When you are
finished, press MENU to close the pop-up window. Then, continue with
step 4.
Then, continue with step 4.
(Continued on next page)
9