Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vanco D2.1
Summary of Contents for Vanco D2.1
-
Page 1: User Guide
Beale Street Audio D2.1 Digital 2.1 Channel Amplifier User Guide... -
Page 2: Important Safety Instructions
Important Safety Instructions RISK OF ELECTRIC SHOCK DO NOT OPEN APPLICABLE FOR USA, CANADA OR WHERE RISQUE DE CHOQUE ÉLECTRIQUE N'OUVREZ PAS APPROVED FOR USAGE CAUTION: TO PREVENT ELECTRIC SHOCK, CAUTION: To reduce the risk of electric shock, do not remove cover (or back). MATCH WIDE BLADE PLUG TO WIDE SLOT, No user-serviceable parts inside. -
Page 3: Table Of Contents
Table of Contents Important Safety Instructions ....................2 Introduction ..........................4 Features ................................. 5 What’s Included ............................5 D2.1 Inputs & Outputs ....................... 6 D2.1 Side Vents .......................... 7 D2.1 IR Remote .......................... 8 Installation ..........................9 Shelf Mount ..............................9 Wall Mount .............................. -
Page 4: Introduction
D2.1 will also team up nicely with other branded speakers... when those situations are just unavoidable. Are you a bass freak? If so, the D2.1 has a line level subwoofer output that can be used to drive a Beale Street Audio subwoofer amplifier and subwoofer for additional bass extension and presence. -
Page 5: Features
• Adjustable Subwoofer Crossover, Slope and Phase settings • Anti-clipping Output Limiter • Bluetooth playback control via IR Remote Control What’s Included 1 - D2.1 Amplifier 1 - AC Power Cord 1 - User Guide Bluetooth Requirements Bluetooth Audio Streaming... -
Page 6: D2.1 Inputs & Outputs
After all connections have been made, connect the supplied AC Power Cord to an unswitched AC power outlet. 2. IR SENSOR - IR sensor ‘sees’ the IR commands from the D2.1 IR Remote, or other properly configured programmable remote to control D2.1 Power, Volume, EQ Input, etc. -
Page 7: D2.1 Side Vents
D2.1 IR Remote or other properly programmed IR System Remote. The D2.1 can be configured to turn ON when an audio signal is present on this input. (See section: Operation/ON/OFF.) The amp will turn OFF when no audio input has been sensed for fifteen minutes. -
Page 8: D2.1 Ir Remote
D2.1 RJ45 Receiver IN jack. Press ►► to forward scan the current track. 11. INPUT SELECT - IN 1 - Press to select the source connected to the D2.1 L&R Line Level IN 2 - Press to select the source connected to the D2.1 Optical IN. -
Page 9: Installation
Shelf SHELF MOUNT The D2.1 can be conveniently mounted on a shelf top as shown. Use wood screws to secure the amp to the shelf to avoid having the amp slide off the shelf and possibly damage the amp, connected cables or other equipment. Leave room for wires. Allow adequate space for airflow. -
Page 10: Connections
All connections are conveniently placed on the side panel for sane wire management, convenient connections and simple service. The illustration shows the D2.1 in a typical home entertainment system for TV audio with stereo in ceiling speakers with an optional subwoofer amp and subwoofer. -
Page 11: Optical In (Tv Audio Connection)
OPTICAL IN (TV AUDIO CONNECTION) 1. Using a Digital Optical Audio cable, (Toslink) connect the Digital Optical Audio OUT on the TV (or other source) to the Optical IN on the D2.1. To select this input, press IN 2 on the D2.1 IR Remote. -
Page 12: Operation
Audio Signal ON Setup via IR Remote NOTE: The D2.1 will default to Line IN out of the box, or if reset to default with Taylor App. In default, it is not necessary to do the following setup if using Line IN to turn the D2.1 ON. -
Page 13: Beale Street Audio Bluetooth Module
Press again to turn Night Mode OFF. SOURCE SELECT IN 1 - Press to select the source connected to the Line L&R jacks on the D2.1. IN 2 - Press to select the source connected to the Digital Optical jack on the D2.1. -
Page 14: Ir Learning
3. Status LED will turn ON. POWER 1. Press the Power button on the D2.1 IR Remote. The Status LED will flash once and turn OFF. 2. Press the button on the system remote to be used for turning the D2.1 ON/OFF. -
Page 15: Mute
5. To exit Learning Mode, press IN 1, otherwise press the next button to be learned. INPUT 3 SELECT 1. Press the IN 3 button on the D2.1 IR Remote. The Status LED will flash once and turn OFF. 2. Press the button on the system remote to be used for IN 3. -
Page 16: Specifications
Specifications AUDIO Maximum Output Power per Channel ....................50W THD+N ................................. <0.5% Signal to Noise (RCA/Bluetooth) ......................78dB Signal to Noise (Optical) ...........................90dB Input Sensitivity ............................. 500mV GENERAL DC Power Supply Output ......................+5VDC/0.5A Line Voltage Range ........................100~240 VAC Standby Power ...............................1W Dimensions ..........5.3”W x 6.9”H x 2”... -
Page 17: Limited Warranty
Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco. This warranty does not apply to those products which have been damaged due to accident, unauthorized alterations, improper repair, modifications, inadequate maintenance and care, or use in any manner for which the product was not originally intended. - Page 18 Notes...
- Page 19 Notes...
-
Page 20: Trademark Information
Trademark Information The Vanco logo, Sonic Vortex logo, and Beale Street Audio Inc. logo are registered trademarks of Vanco International, LLC. Vanco, Sonic Vortex, Beale Street Audio, Get Reale. Get Beale., the Vortex logo, and the Beale Street Audio logo are trademarks of Vanco International, LLC.
Need help?
Do you have a question about the D2.1 and is the answer not in the manual?
Questions and answers