Advertisement
Quick Links
U5047A PAG QUASAR INSTRUCTION MANUAL
PAG Quasar
All-Chemistry Charging System
Instruction Manual
CONTENTS
SECTION
1
SAFETY
2
3
4
5
6
SECTION 1
1.1
1.2
1.3
1.4
1.5
1.6
PAGE
1.7
2
3
6
7
1.8
12
14
1.9
1
U5047A PAG QUASAR INSTRUCTION MANUAL
SAFETY
This manual contains important safety and operating instructions.
Please read these fully and note all warnings before using the charger.
Please follow all instructions and retain this manual for future
reference.
PAG Quasar chargers are not intended for any use other than the
charging of batteries and the powering of broadcast cameras as
detailed in Section 2 , Specification, Page 3.
IMPORTANT: Use only on AC supplies 100V-250V, 47-63Hz or with
PAG approved voltage converters. Connection of the supply to the
unit should be made using only the standard lead provided with this
equipment.
Protect the power cord from being walked on or pinched. Unplug this
apparatus during lightning storms or when unused for long periods of
time.
Ensure that the ventilation slots are not obstructed when in use, e.g.
do not site the charger on a carpet, or cover when in use.
WARNING: Indoor use only. To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
Although the charger is reverse polarity and short circuit protected,
extreme care should always be taken not to short circuit the battery
itself. Rechargeable batteries can deliver power at a very high rate,
and short circuiting even a partially charged battery could result in a
fire or personal injury. PAG supplies a range of connector leads for
most charging requirements, and does not accept responsibility for
any other form of charging connection.
Do not disassemble the charger. There are no user-serviceable parts
inside. Incorrect re-assembly may result in a safety hazard.
Double Insulation: When servicing use only identical replacement parts.
2
Advertisement
Related Manuals for PAG PAG Quasar
Summary of Contents for PAG PAG Quasar
-
Page 1: Table Of Contents
Please follow all instructions and retain this manual for future reference. PAG Quasar chargers are not intended for any use other than the charging of batteries and the powering of broadcast cameras as detailed in Section 2 , Specification, Page 3. -
Page 2: Specification
U5047A PAG QUASAR INSTRUCTION MANUAL 1.10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the supply cord or plug has been damaged, liquid has been spilled, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. -
Page 3: Installation
Models 9727 & 9753: 844g (1.86lbs approx.). SECTION 3 INSTALLATION All Quasar chargers are fitted with a mains input socket conforming to CEE22 (IEC socket). This is situated on the back panel. Mains supply connection to the charger should only be made using the standard lead supplied with this equipment. -
Page 4: Operating Instructions
The LCD screen will illuminate and briefly display the PAG logo and charger model before entering normal operating mode. With no batteries connected, all channels will indicate absent. Quasar chargers may be disconnected from the supply at any time in complete safety and without damage to the charger or any batteries connected. - Page 5 The first battery to be connected, irrespective of the channel chosen, will be the first battery selected. NOTE: Quasar chargers offer a choice of connector on each channel. Batteries may be connected to either but not both connectors at the same time.
-
Page 6: Servicing & Repairs
To exit Power Supply Mode: turn the camera OFF. Power Supply Mode will remain engaged until the Function Button is operated for one second, which will return the Quasar to Charging Mode. The Quasar will auto-matically revert to Charging Mode if the mains supply is disconnected. -
Page 7: Warranty
WARRANTY Notwithstanding any provision of any agreement the following Warranty is exclusive: PAG Limited warrants each PAG Quasar charger it manufactures to be free of defects in material and workmanship under use and service for two years from the date of purchase. This warranty extends only to the original purchaser.