Download Print this page

NEC DT820 Quick Install Manual

Multiline ip terminals.
Hide thumbs

Advertisement

The SL2100
Quick Install Guide:
Multiline IP Terminals
www.nec-enterprise.com

Advertisement

   Also See for NEC DT820

   Summary of Contents for NEC DT820

  • Page 1

    The SL2100 Quick Install Guide: Multiline IP Terminals www.nec-enterprise.com...

  • Page 2

    DT820 Phones (ITY-6D/ITY-8LDX) 8IPLD DESI-Less Phone Note: For more information on your SL2100 Communications System and NEC Multiline IP Terminal, including Quick User Guides and User Guides, navigate to your phone’s Support page on the NEC Businessnet Portal. NEC SL2100 Communication System...

  • Page 3

    Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Other Documentation available:  SL2100 Hardware Manual  SL2100 Features and Specifications Manual  SL2100 Networking Manual NEC SL2100 Communication System...

  • Page 4: Table Of Contents

    6- IP7WW-8IPLD-C1 DESI-Less IP Terminal Leg Adjustment ................12 Low Position Setting ............................12 High Position Setting ............................13 7- DT820 IP Terminal Leg Adjustment (ITY-6D-1 and ITY-8LDX-1) ..............14 Low Position Setting ............................14 High Position Setting ............................15 8- Wall Mounting Multiline IP Terminals ......................16 9- Multiline IP Terminal Configuration ........................

  • Page 5: Sl2100 Multiline Ip Terminals

    (Optional BE110790) (Optional BE110790) By EHS Cable (Plantronics By EHS Cable (Plantronics By EHS Cable (Plantronics EHS Support APD-80 APD-80 APD-80 License Built-in Terminal NEC SIP License NEC SIP License EU909388 EU909388 Requires one license per Terminal. NEC SL2100 Communication System...

  • Page 6: Parts Available For The Sl2100

    1 x Declaration of Conformity Additional Items Required:  Ethernet (cat5e/cat6) cable(s)  NEC SIP License (Installed on SL2100) ITY-8LDX-1 (BK) TEL Multiline IP Terminal 1 x ITY-8LDX-1 Multiline IP Terminal 1 x Declaration of Conformity Additional Items Required: ...

  • Page 7: 2- Features

    Quick Install Guide – SL2100 Multiline IP Terminals rev 1.1 2- Features IP7WW-8IPLD-C1 Multiline IP Terminal ITY-6D-1 Multiline IP Terminal NEC SL2100 Communication System...

  • Page 8

    Quick Install Guide – SL2100 Multiline IP Terminals rev 1.1 ITY-8LDX-1 Multiline IP Terminal NEC SL2100 Communication System...

  • Page 9: 3- System Connection Overview

    The Multiline IP Terminals support PoE power provisioning for the telephone.  PoE(IEEE802.3af) PoE (Power Over Ethernet) is a LAN technology that allows standard 10-Base-T/100Base- TX/1000Base-TX data cables to pass electrical current from a power source to a requesting end device. NEC SL2100 Communication System...

  • Page 10: Ethernet Sockets For Voip

    Data (eg PCPro/WebPro, SMDR etc) VOIP LAN speed 100/1000 Mbps Full Duplex Use the IP address and Subnet mask setup in PCPro Easy Edit - Quick Install - Cards-CPU Settings - CPU IP Address: VOIP IP Address NEC SL2100 Communication System...

  • Page 11: Check The Ip Address Of The Sl2100

    System IP address is setup in PCPro Easy Edit - Quick Install – Cards - CPU Settings - CPU IP Address: IP Address VoIPDB IP address is setup in PCPro Easy Edit - Quick Install – Cards - CPU Settings - CPU IP Address: VOIP IP Address NEC SL2100 Communication System...

  • Page 12: 6- Ip7ww-8ipld-c1 Desi-less Ip Terminal Leg Adjustment

    Low Position Setting 1. Turn telephone over (button side down). 2. Adjust the legs to Low Position height. 3. Lead the Line and Handset cords through the applicable grooves. 4. Turn telephone over (button side up). NEC SL2100 Communication System...

  • Page 13: High Position Setting

    1. Turn telephone over (button side down). 2. Pull up the Leg Stoppers. 3. Adjust the legs to High Position height. 4. Lead the Line and Handset cords through the applicable grooves. 5. Turn telephone over (button side up). NEC SL2100 Communication System...

  • Page 14: 7- Dt820 Ip Terminal Leg Adjustment (ity-6d-1 And Ity-8ldx-1)

    Quick Install Guide – SL2100 Multiline IP Terminals rev 1.1 7- DT820 IP Terminal Leg Adjustment (ITY-6D-1 and ITY-8LDX-1) The Multiline IP DT820 terminals provide adjustable legs for angling the phone to best suit each user. The leg can be set for two different heights (Low/High).

  • Page 15: High Position Setting

    1. Turn telephone over (button side down). 2. Pull up the Leg Stoppers. 3. Adjust the legs to High Position height. 4. Lead the Line and Handset cords through the applicable grooves. 5. Turn telephone over (button side up). NEC SL2100 Communication System...

  • Page 16: 8- Wall Mounting Multiline Ip Terminals

    2. Attach the IP4WW-WALL MOUNT UNIT to the bottom panel and arrange the cables as shown below. 3. Remove the switch-hook from the unit. Turn the tab toward the top. Then slide the hook-switch into position. 4. Install two screws into a wall. The screw head must be remained about 3mm (0.12”). NEC SL2100 Communication System...

  • Page 17

    Quick Install Guide – SL2100 Multiline IP Terminals rev 1.1 5. Mount the telephone on the wall. NEC SL2100 Communication System...

  • Page 18: 9- Multiline Ip Terminal Configuration

    This is because, at this point the terminal does not know the IP address of the SL2100 to connect to, which needs to be configured next. Terminal receives power and begins its initial boot sequence. Terminals firmware is loaded into memory and applications started. NEC SL2100 Communication System...

  • Page 19: Multiline Ip Terminal Programming Interface

    Quick Install Guide – SL2100 Multiline IP Terminals rev 1.1 DT820 Terminals Only an LLDP discovery request is sent to the network and if supported by the network switch, configuration details of the network such as VLAN and QoS configuration can be obtained by the terminal.

  • Page 20: Configure 8ipld Multiline Ip Terminal

    1. Once logged in successfully, the Admin Menu options will be available. 2. Press 2 to select SIP Settings and press the OK soft key. 3. The SIP Settings menu will now be displayed. 4. Press 2 to select Server Address & URI. NEC SL2100 Communication System...

  • Page 21

    Server Address. 7. The 1 Server Address data entry screen will now be displayed. Enter the VOIP IP address of the SL2100. Press the OK soft key when finished. 8. Press 4 to select SIP Server Port. NEC SL2100 Communication System...

  • Page 22

    Server Port data entry screen will now be displayed. The value should be 5080, if it is not, then enter 5080 here. Press the OK soft key when finished. 12. Press the Exit soft key 2 times. When you are back at the main Admin Menu press the Save soft key. NEC SL2100 Communication System...

  • Page 23

    14. If successful the Multiline IP terminal will be allocated an available port on the system and display it’s extension number information. 15. The IP terminal is now registered and ready to be used with the SL2100. NEC SL2100 Communication System...

  • Page 24: Configure Dt820 Multiline Ip Terminals

    Quick Install Guide – SL2100 Multiline IP Terminals rev 1.1 Configure DT820 Multiline IP Terminals Please note these screens are taken for the 8LDX model of DT820. The 6D configuration is identical to this procedure only the display is smaller on that model.

  • Page 25

    7. The 1 Server Address data entry screen will now be displayed. Enter the IP address of the SL2100 VoIPDB interface. Press the OK soft key when finished. 8. Press 4 to select SIP Server Port. NEC SL2100 Communication System...

  • Page 26

    Server Port data entry screen will now be displayed. The value should be 5080, if it is not, then enter this value here. Press the OK soft key when finished. 12. Press the Exit soft key 2 times. When you are back at the main Admin Menu press the Save soft key. NEC SL2100 Communication System...

  • Page 27

    14. If successful the Multiline IP terminal will be allocated an available port on the system and display it’s extension number information. 15. The IP terminal is now registered and ready to be used with the SL2100. NEC SL2100 Communication System...

This manual also for:

Sl2100 Ity-6d 8ipld Ity-8ldx Be116517 Be115113... Show all

Comments to this Manuals

Symbols: 0
Latest comments: