Table of Contents
Advertisement
before operating your
appliance for the first time
Installing your oven accessories
The type of oven accessories you receive is dependant on
the model you have purchased.
1. Shelves and trays
WARNING
caution
Ensure the shelves are inserted in the correct orientation,
otherwise you may damage the appliance.
Your oven comes with formed "easy clean" shelf supports.
The shelves are designed to travel freely on the shelf supports
without being pulled out accidentally. Make sure you have
the shelf in the correct orientation before you slide it in.
Otherwise it could become jammed.
• Locate the rear edge of the shelf in the recess between
2 formed shelf supports. See diagram below.
NOTE: The top 'ledge' is not a shelf position.
note the orientation of the
side and rear features
• With the front edge raised, begin to slide the shelf into the
oven. Lower the front edge as you push the shelf fully in.
• The grill/baking tray for underbench oven models sits into
a wire carrier that fits into the oven exactly like the shelves.
• The grill/baking tray for separate grill wall oven models
slides into the wire runners in a similar manner.
• When fully inserted, the shelf/tray should not interfere
with the closed oven door.
2. Main oven wire side racks (where applicable)
The side racks that come with your oven can be attached
to either side of your oven.
• Insert the twin pegged side into the rear access holes
provided, ensuring that the pegs are fully inserted.
• Then locate the front peg into the front access hole
and push in firmly.
6 BEFORE OPERATING YOUR APPLIANCE Built-in Cooking
• When locating the left side rack into the small oven or
grill, ensure the pegs are inserted into the upper two
access holes.
3. Separate grill side racks (where applicable)
Separate grill wall ovens come with side racks that are to
be fitted to the smaller lower grill/oven.
These can be attached to either side in the following manner:
• Insert the largest peg into rear access hole provided.
See diagram above.
• Then locate the front peg into the front access hole and
push in firmly.
• When locating the left side rack into the small oven or
grill, ensure the pegs are inserted into the upper two
access holes.
before operating your
appliance for the first time
Shelves and trays (CVEP604 and CVE602)
important
TIPS & INFORMATION
The shelves are designed so that they have maximum travel
but cannot be accidentally pulled right out. The trays are
designed the same way and fit straight into the side racks.
To fit a shelf or tray to side racks:
• Locate the rear edge of the shelf/tray inbetween 2 guide
rails of the side rack - see diagram. Ensure the same rail
positions on both sides of the oven are being engaged.
• With the front edge raised, begin to slide the shelf into
the oven.
• Once the detents have passed the front edge of the side
rack, the shelf can be pushed fully in.
• The grill/baking tray for separate grill wall oven models
slides into the wire runners in a similar manner.
• When fully inserted the shelf/tray should not interfere
with the closed oven door.
• Remove extra trays and dishes before roasting or baking.
To fit a shelf or tray to telescopic slides (where fitted):
• With the slides fully pushed in, push the shelf or tray along
the top of the slide until it hits the back post.
• Drop the front of the shelf or tray onto the slide ensuring
it sits behind the front post of the slide.
• When fully inserted the shelf/tray should not interfere with
the closed oven door.
NOTE: Shelves and accessories must be removed when
using pyrolytic cleaning function.
Back post
Front post
Pizza Stone
• Insert the pizza rack into the grill side racks (lower oven)
as shown in the image below.
• Note the orientation of the pizza rack. Refer to the image
below.
• Carefully place the pizza stone inside the pizza rack.
• Slide the pizza rack fully in and close the door.
Grill Side Rack
Pizza Stone
Pizza Rack
Built-in Cooking BEFORE OPERATING YOUR APPLIANCE 7
Advertisement
Table of Contents
