Related Manuals for Triax CG2CT 860 C
Summary of Contents for Triax CG2CT 860 C
- Page 1 Head-End Digital Modulator 2 x DVB-C2/T2 CG2CT 860 C Art. No. 325041 Assembly Instructions As well as this supplementary Assembly Instructions, the Assembly Instructions for the CSE 2800 apply. TRIAX - your ultimate connection...
- Page 2 o n t e n t s 1 Safety regulations ....................3 2 General information ..................4 Scope of delivery ................4 Meaning of the symbols used ............... 4 Technical data..................4 Description ..................5 How the TPS module works ..............6 Station filter ..................
- Page 3 Renaming a PID ................29 Output data rate ................30 Network Information Table (NIT) ............31 Factory reset ..................32 Saving data ..................33 6 Final procedures ....................34 7 Channel and frequency tables ................35 a f e t y r e g u l a t i o n s •...
- Page 4 2.1 s C o p e d e l i v e ry 1 Digital Transmodulator QAM "CG2CT 860 C" 1 RF connection cable 1 CD (assembly instructions) 1 Brief Assembly Instructions 2.2 m...
- Page 5 "BE-Flash" via the 9-pin D-SUB socket on the head-end station. You can find the current operating software for the head-end station and the QAM module, the software "BE-Flash" and the current assembly instructions on the website "www.triax.com". The QAM module is designed exclusively for use in the CSE 2800 head-end station.
- Page 6 2.5 h tps t h e m o d u l e wo r ks After decoding the satellite signals, the demodulated data streams can be accessed via the integrated TPS module. These data streams, also called trans- port streams, contain several stations with all their components (video, audio, data and service information), which can be changed using the TPS module.
- Page 7 3.1 r Ca e t r o f i t t i n g m o d u l e The module is equipped with two common interfaces. This allows you to con- nect two CA modules for various scrambling systems and service providers. Scrambled channels can only be descrambled with a CA module suitable for the scrambling system and the corresponding smart card.
- Page 8 3.2 i Qam n s ta l l i n g t h e m o d u l e – Check that the plug contacts of the CA module are tightly seated in the terminal strips on the common interface of the QAM module and make sure there is reliable contact.
- Page 9 3.3 C Qam o n n e C t i n g t h e m o d u l e Fig. 4 • Connect the RF inputs (input "A") and (input "B") on the QAM mod- ule (fig. 4) to corresponding signal sources via the preinstalled F terminals in the rear wall of the head-end station through the cable inlets using RF cables made on-site.
- Page 10 C o n t r o l p a n e l g l a n C e 4.1 f u n C t i o n s t h e C o n t r o l pa n e l b u t to n s To move the cursor To adjust values and...
- Page 11 • Test the software versions of the head-end station and the QAM module and update them if necessary. The current software versions can be found on the website "www.triax.com". • Connect the test receiver to the modulator output on the QAM module or to the RF output on the output collector if it is already connected (page 9).
- Page 12 5.3 p r o g r a m m i n g p r o C e d u r e Bedienhinweise Operating Hints SETUP BE160 Ein/On "blättert" Menüs vorwärts. scrolls forward through the menu. V 10 wählen die Eingabeposition select the enter position.
- Page 13 Bx 2A FREQ 746.00 Bx 2A TV + 01/04 arte Bx 2A Bx 2A 01/05 MENU PID Check on => Information *) nur mit CA-Modul/ Bx 2A SKIP CA only with CA module *) Die angezeigte Information ist abhängig PID 1: 0x0000 vom verwendeten CA-Modul.
- Page 14 Werkeinstellung Bx 2 FACTORY Bx 2 FACTORY aufrufen page 12 invoke factory defaults Defaults => STORE => S Bx 2 MEMORY Einstellung speichern page 12 store factory defaults S => STORE STORE page 12 CANCEL 5.4 p Qam r o g r a m m i n g t h e m o d u l e Notes:...
- Page 15 e l e C t i n g t h e m o d u l e C h a n n e l s t r i p • If necessary, press repeatedly to select the particular module (Bx …) to be programmed.
- Page 16 o d u l ato r o f f e v e l This menu item is used to set the output levels of the modulators of the module to the same value and to level them to the output levels of the modulators of other modules used and to switch the modulators on or off.
- Page 17 Channel setting: 2A/B FREQ 834.00 MHz • Use buttons to select the cursor position for channel setting. • Use buttons to adjust the desired channel. Frequency setting (42,0 MHz … 860,0 MHz): 2A/B FREQ 834.00 MHz • Use buttons to select the cursor position for frequency setting. •...
- Page 18 In this case increase the output symbol rate or the QAM modulation or remove stations from the data stream using the station filter. QAM-Modulation: In this menu item you can set the QAM modulation. —> For higher QAM modulation, the output symbol rate is lowered. An output QAM modulation of >...
- Page 19 u b s t i t u t e s i g n a l t h e C a s e i n C o r r e C t i n p u t s i g n a l You use this menu to set whether a "Single Carrier"...
- Page 20 n p u t pa r a m e t e r In this menu you select the channel strip (line) for which you would like to do the input parameter settings in the related submenus. Bx 2 INPUT Tuner A OK =>...
- Page 21 / s h ys i C a l ay e r i p es l i C es —> This menu is only displayed if you have selected "T2" or "C2" for the kind of modulation. In this menu, you enter the parameter(s) PLP (DVB-T2) or PLP and SLICE (for DVB-C2), which are required for the selection of the data stream.
- Page 22 • Press buttons to set the desired channel/frequency. —> Once the RF receiver has synchronised to the input signal, "OK" is displayed. —> If "– –" appears in the second line of the display, there is no input signal present. Check the configuration of the antenna system and the head-end station as well as the preceding settings of the module.
- Page 23 —> All stations from the channel strip will be read, and then displayed with name and station type. —> If no station is found, the following message will appear in the dis- play: "FILTER no Service". In this case, check the configuration of the antenna system and head-end station, as well as the previously adjusted settings for the module.
- Page 24 • Press the button. –> The "PID monitoring" – "CA" submenu is activated. pid m o n i to r i n g In this menu you can switch off the PID monitoring and call up a menu for the settings of the CA module (dependent on the CA module).
- Page 25 m o d u l e The menu varies according to which CA module you are using. For this rea- son, please refer to the operating manual of your particular CA module. The relevant information is shown in the display of the head-end station. This may appear as a fixed display or as scrolling text according to display capabilities.
- Page 26 C o n o m i z e d es C r a m b l i n g C a paC i t y In this menu up to 9 not needed PIDs (e.g. audio PIDs of foreign language versions) can be excluded from the descrambling in order to economize de- scrambling capacity.
- Page 27 p t i o n s e t t i n gs In this menu you select the channel strip for which you would like to do the option settings in the related submenus. Bx 2 OPTIONS => —> In order to skip the "Option settings", press button •...
- Page 28 • Press the button. —> The "BAT/SDT-OTHER tables" – "BAT/SDT" submenu is activated. bat/sdt-other ta b l es In this menu you can switch on resp. off the BAT- and SDT-OTHER tables. —> BAT = Bouquet Association Table: Information in the data stream about the affiliation of station packets to a specific bouquet.
- Page 29 pid e l e t i n g In this menu a PID of the transport stream can be deleted. 2A/B DROP 0x0000 • Use the buttons to place the cursor under the respective digit of the hexadecimal number of the PID to be deleted ("0x0000") and set the hexa- decimal number using •...
- Page 30 —> The "Output data rate" – "DATARATE" main menu is activated. u t p u t data r at e This menu shows the output data rate defined using the QAM settings and the current needed output data rate. Bx 2 DATARATE ! ! ! 36/51 Mb...
- Page 31 (nit) e t wo r k n f o r m at i o n a b l e Bx 2 => Make • To switch NIT "on" resp. "off" press the buttons. • Press the button to activate NIT ("Make"). All active modules which are able to output a NIT ("NIT modules") must be set and ready for reception.
- Page 32 aC to ry r e s e t In this menu you can reset all settings to the factory defaults. Bx 2 FACTORY Bx 2 FACTORY Defaults => STORE => S • Press the button. —> The factory defaults are invoked ("FACTORY STORE"). —>...
- Page 33 av i n g data Bx 2 MEMORY STORE S => STORE CANCEL • All programmed data is saved by pressing the button. You will be returned to the menu item "Selecting the module / channel strip" via (page —> By pressing the button, you will be returned to the menu item "Selecting the module / channel strip"...
- Page 34 i n a l pro C e d u res After installing the head-end station, upgrading accessories or installing mod- ules it is necessary to tighten all cable connections, cable terminals and cover screws in order to maintain compliance with current EMC regulations. • Securely tighten the cable connections using an appropriate open-ended spanner. • Test the output level of the output collector according to the CSE 2800 as- sembly instructions and set the output level required for the cable system. •...
- Page 35 h a n n e l a n d f r e Q u e n C y t a b l e s Advice for a frequency grid (8 MHz) in the band I/III 42.00 82.00 146.00 186.00 226.00 266.00 50.00 114.00...
- Page 36 Service: TRIAX A/S • Bjørnkærvej 3 • DK-8783 Hornsyld Alterations reserved. Technical data E. & O.E. V8/17102014...