Related Manuals for Triax CCS-2 2001
Summary of Contents for Triax CCS-2 2001
- Page 1 Head-End Digital Modulator HDTV / COFDM CCS-2 2001 C LASS Art. Nr. 325157 Assembly Instructions TRIAX - your ultimate connection...
-
Page 2: Table Of Contents
Selecting the cassette ..............16 Output signal ................17 Output level ................17 Modulator ................17 Output parameter ..............17 COFDM parameters ..............18 COFDM settings ................21 Bandwidth of the output signal ..........21 Carrier modulation ..............21 Inverting the user signal ............21 - 2 - CCS-2 2001... - Page 3 Programming via the control software ..........38 Quick setup via configuration file ..........38 Creating/exporting a configuration file ........38 Importing a configuration file ...........40 Service-ID (SID) ................41 6 Final procedures ..................43 7 Channel and frequency tables ..............44 - 3 - CCS-2 2001...
-
Page 4: Safety Regulations And Notes
European Council from January 27, 2003 which addresses old electronic and electrical devices, such devices must be disposed of at a designated collection facility. At the end of its service life, please take your device to one of these public collection facilities for proper disposal. - 4 - CCS-2 2001... -
Page 5: General Information
C o n t e n t s 1 Cassette CCS-2 2001 2 HF cables 1 Brief assembly instructions... -
Page 6: Description
The COFDM modulated HF output signals are sent through the HF output of the cassette to the output collector. The common output level of the channel strips can be set at the output collector. Software update for the operating software of the cassette is possible via satellite. - 6 - CCS-2 2001... -
Page 7: Software Query
"V 44" or higher. You can find the current operating software for the control unit, the software "BE-Flash" and the current assembly instructions on the website "www.triax.com". The cassette is intended for use in CSE 3300 head-end systems. o f t wa r e q u e ry... -
Page 8: Changing The Nit
– Before installing or changing a cassette unplug the power cable from the mains power socket. • Remove the fastening screws of an unoccupied slot from the bracket of the head-end station. • Insert the cassette in this slot and push it into the housing. • Align the cassette and apply slight pressure to connect it to the connections of the board and the HF bus bar. • Fasten the cassette with the screws 0° - 8 - CCS-2 2001... -
Page 9: Emc Regulations
Tighten the nuts of the cable terminals until the teeth on the lock washers put under have penetrated the exterior coating and a good connection is made between the housing / 19" cabinet and cable terminals. - 9 - CCS-2 2001... -
Page 10: Overview Of The Cassette
9-Pin D-SUB socket "RS-232" using a PC or notebook and the software "BE-Flash". You can find the current operating soft- ware on the website "www.triax.com". o n n e C t i n g t h e C a s s e t t e • Connect the HF connections to the inputs... -
Page 11: Retrofitting A Ca Module
(top) of the CA module • Insert the CA module into the slot with the top side of the CA module facing the top side of the cassette. • Push the CA module without canting into the guide rails of the CA slot and contact it to the common interface. - 11 - CCS-2 2001... -
Page 12: The Control Panel At A Glance
The key pad on the head-end station is used to scroll through the menus step-by-step: scrolls forward through the menus. select parameters in the menus. set values, initiate actions. selects sub-menus. scrolls backward through the menus. saves all entries. - 12 - CCS-2 2001... -
Page 13: Programming
In order to prevent interference within the head-end station and the cable sys- tem, the output level of the cassette must be decreased by 8 dB compared to analogue cassettes. • Measure the output levels of the other cassettes and tune them to a uniform output level using the appropriate level controls or software dependent on the head-end station used. Please regard the assembly instructions of the respective head-end station. - 13 - CCS-2 2001... -
Page 14: Programming Procedure
▶ 4A/B SYMBOL DVB-S / QPSK… / 8PSK… / DTV… 27500 DVB-S 27500 / 22000 4A/B FREQ ◀ ▶ 11836 -1.8 CN 12 ◀ ▶ 4A/B – 01/10 - 14 - CCS-2 2001 + / - / X Das Erste... - Page 15 UPDATE off => 0x1C49 0x0030 on / off ◀ ▶ Page 14 auf Werkseinstellung Bx 4 FACTORY Bx 4 FACTORY zurücksetzen und speichern ▶ reset to factory defaults Defaults => STORE => M and store - 15 - CCS-2 2001...
-
Page 16: Programming The Cassette
• Select the cassette you want to programme (e.g. Box 4) by repeatedly press- ing the button if necessary. —> The display shows e.g. the menu "Box 4 DVBS2-CIM": "Box 4" stands for slot 4 "DVBS2-CIM" Type of cassette "V 4" Software version of the cassette - 16 - CCS-2 2001... -
Page 17: Output Signal
In this submenu you can set the output parameter of the COFDM-Signal. —> To skip the setting of the output parameters press the but- ton. The "Output channel / Output frequency" – "OUTPUT" main menu is activated (page 24). - 17 - CCS-2 2001... -
Page 18: Cofdm Parameters
16 QAM 14929 16588 17564 18096 16588 18431 19516 20107 17418 19353 20491 21112 14929 16588 17564 18096 19906 22118 23419 24128 64 QAM 22394 24882 26346 27144 24882 27647 29273 30160 26126 29029 30737 31668 - 18 - CCS-2 2001... - Page 19 16 QAM 11197 12441 13173 13572 12441 13824 14637 15080 13063 14515 15369 15834 11197 12441 13173 13572 14929 16588 17564 18096 64 QAM 16796 18662 19760 20358 18662 20735 21995 22620 19595 21772 23053 23751 - 19 - CCS-2 2001...
- Page 20 Used bandwidth [MHz] 5.71 5.71 5.71 Total symbol duration 373 336 317 308 767 672 634 616 1493 1344 1269 1232 [µs] Guard interval T [µs] 74.7 37.3 18.7 9.3 37.4 18.6 298.7 149.3 74.6 37.3 - 20 - CCS-2 2001...
-
Page 21: Cofdm Settings
"NEG". The default setting is "POS". • Use to place the cursor under "POS". • Use to set the spectral position to "NEG". • Press the button. —> The "Transmission parameters" – "COFDM-MODE" menu is activated. - 21 - CCS-2 2001... -
Page 22: Transmission Parameters
In this menu item you set the relation of the duration of the user symbols to the duration of the guard intervals to be transmitted. A high guard interval, e.g. "G1/4" causes a low output data rate. For cable networks the setting "G1/32" is adequate. • Use the buttons to place the cursor under "G…". • Set the guard interval required using the buttons ("G1/4", "G1/8", "G1/16", "G1/32"). - 22 - CCS-2 2001... -
Page 23: Transmitter Identification
• Press the button. —> You will be returned to the "Output signal" – "OUTPUT" main menu (page 17). • Press the button. —> The "Output channel / Output frequency" – "OUTPUT" main menu is activated. - 23 - CCS-2 2001... -
Page 24: Output Channel / Output Frequency
—> The corresponding frequency is displayed. • Press the button. —> The "Input parameters" – "INPUT" main menu is activated. - 24 - CCS-2 2001... -
Page 25: Input Parameters
• To set other oscillator frequencies use the buttons to place the cursor under the digit of the oscillator frequency displayed to be set. • Press to enter the respective digit of the oscillator frequency of the LNB used. • Repeat the procedure by the quantity of the digits to be set. - 25 - CCS-2 2001... -
Page 26: Input Symbol Rate
Setting the DVB mode • Use the button to place the cursor under "DVB-S" and set the required DVB-S2-mode with the buttons. • Press the button. —> The "Setting the input frequency" – "FREQ" menu is activated. - 26 - CCS-2 2001... -
Page 27: Setting The Input Frequency
—> If stations are selected, the quality of the received transport stream (level and C/N) is indicated by a status LED. Status LED Tuner A Status LED Tuner B LED indicator Indication Green Signal quality is good Signal quality is insufficient Yellow No signal - 27 - CCS-2 2001... -
Page 28: Station Selection
Meaning of the indicators in the example: "Bx 4A" Slot 4, channel strip "A" "TV" TV channel type " – " The selected station is not activated. "01/10" The 1st of 10 stations is being displayed. "Das Erste" Station name - 28 - CCS-2 2001... -
Page 29: Descrambling Stations
Change the service ID (SID) By default the SIDs are set automatically. When required the SID can be set manually. • Press the button. —> The submenu for SID setting is activated. 4A/B 01/10 0x6DCA => auto - 29 - CCS-2 2001... - Page 30 —> Return to the "Input parameter" – "INPUT" main menu (page 25). • Set the input parameters of Tuners "B" analogous to the settings of Tuner "A". • Press the button. —> The "PID monitoring" – "CA" main menu is activated (page 31). - 30 - CCS-2 2001...
-
Page 31: Operation With A Ca Module
This may appear as a fixed display or as scrolling text according to display capabilities. Bx 4 Bx 4 01/03 MENU ▶ PID Check => Information *) - 31 - CCS-2 2001... -
Page 32: Output Data Rate
31667 (= "Number 1"): Maximum gross output data rate (25772) (= "Number 2"): The current measured gross output data rate. If the station filter is set correctly, this value is lower than the value of the "Number 1". The value fluctuates, since the data rates of individual stations are dynamically modified by the broadcasters. - 32 - CCS-2 2001... -
Page 33: Transport Stream Id And The Orgnet-Id
"off" and switch "on" the trans- mitter identification using the buttons. —> By pressing the button you return to the hexadecimal number setting. • Press the button. —> The "Network Information Table" – "NIT" menu is activated. - 33 - CCS-2 2001... -
Page 34: Network Information Table (Nit)
• To switch off the new NIT ("off") press the button. —> The NITs of the other …-COFDM cassettes will stay switched on. When the NIT of the cassette is switched on again ("on") by press- ing the button, the previously generated NIT is added again. If you have changed parameters in the meantime, you must first select "Make" to generate a new, up-to-date NIT. - 34 - CCS-2 2001... -
Page 35: Nit Version
—> Before a NIT must have been created. • Use the buttons to set the desired NIT version (0…31). • Press the button. —> Return to main menu "NIT". Bx 4 => Make • Press the button. —> The "Software update" – "OTA" menu is activated. - 35 - CCS-2 2001... -
Page 36: Software Update
MOD ID number to be set. • Press to set the respective MOD ID. • Press the button. —> Return to the "Software update" – "OTA" main menu. • Press the button. —> The "Factory reset" – "FACTORY Defaults" menu is activated. - 36 - CCS-2 2001... -
Page 37: Factory Reset
—> Returning to "Selecting the cassette" menu (page 16). —> The settings are saved. —> If functions of the TPS module are activated, their status is shown in the second line of the menu: "N" – NIT is activated. —> By pressing the button, you will be returned to the menu item "Output signal" without saving the programmed data (page 17). - 37 - CCS-2 2001... -
Page 38: Programming Via The Control Software
P o r t i n g a C o n f i g u r at i o n f i l e • Select the cassette in the left window of the CCRS 1000 (tree structure) and activate the menu "Data settings" e.g. using button • Perform all settings. • Activate the "MTP function" e.g. using - 38 - CCS-2 2001... - Page 39 • Herein also perform all settings. • Return to the menu "Data settings" e.g. using button • Click on button to export the configuration. • Enter a file name, select the target directory and store the file. - 39 - CCS-2 2001...
-
Page 40: Importing A Configuration File
• Select the file from the source directory and import the configuration using button • In order to get a correct indication of the filter settings, the configuration data must be transferred ( ) to the cassette and then imported ( ) from the cassette again. - 40 - CCS-2 2001... -
Page 41: Service-Id (Sid)
—> For basic operations of the software please note the operating in- structions CCRS 1000, you will find on the CD added. • Select the cassette in the left window of the CCRS 1000 (tree structure) and activate the "MTP function" e.g. using button • Activate the check box beside the desired service and click on the service in section "Input" (tab "Services") • Click on button - 41 - CCS-2 2001... - Page 42 • Enter the desired SID in form of a hexadezimal value (e.g. 5678) and click on button —> The changed SID is displayed in section "Input" (tab "Services") and in Section "Output/Remapping" in form of a hexadezimal / dezimal value. —> The changes are only effective when they were sent to the cassette - 42 - CCS-2 2001...
-
Page 43: Final Procedures
• Securely tighten the cable connections using an appropriate open-ended spanner. • Measure the output levels of the other cassettes and tune them to a uniform output level using the appropriate level controls or software dependent on the head-end station used. Please regard the assembly instructions of the respective head-end station. • Mount the front cover (see assembly instructions of the head-end station). - 43 - CCS-2 2001... -
Page 44: Channel And Frequency Tables
C 48 690.00 C 58 770.00 C 68 850.00 C 29 538.00 C 39 618.00 C 49 698.00 C 59 778.00 C 69 858.00 C 30 546.00 C 40 626.00 C 50 706.00 C 60 786.00 - 44 - CCS-2 2001... - Page 45 Alterations reserved. Technical data E. & O.E. V4/24102011...