Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Projecta BLT700
Summary of Contents for Projecta BLT700
- Page 1 12 VOLT BATTERY & ELECTRICAL SYSTEM ANALYSER P/No. BLT700...
-
Page 2: Kit Contents
10. Status indicator (GREEN) 11. Power indicator (RED) 12. Thermal printer INSTALLING PAPER SETUP 1. Connect clips to battery. Bootup screen should briefly be displayed. If error is displayed check clamps 2. Brightness adjust 3. Setting Time & Date BLT700... -
Page 3: Continue Testing
MAIN MENU 1. New test Select this option to start a new set of tests. Enter a unique reference for the test e.g. vehicle licence plate number 2. Continue testing Select this option to add more test results to those last viewed or stored in memory 3. -
Page 4: Delete Results
4. Delete results SINGLE Result: Select result to delete then press ‘Enter’, press ‘Enter’ again to confirm delete ALL Results: Pressing < and > keys for a few seconds will delete ALL results in memory 5. Select battery range After selecting ‘new test’ or ‘continue testing’, select a suitable battery range 1. -
Page 5: Battery Test
BATTERY TEST Select this option to check cranking ability of the vehicle battery. If a vehicle has recently been used, the battery may have a surface charge, which could effect the results. If this is the case you will be prompted to turn on the headlights until the surface charge has been removed. If the battery voltage is low (below 12 volts) it may still be tested but a warning will be given prior to starting the test. - Page 6 5. For JIS ratings, refer to supplied conversion chart to get CCA value 6. Enter battery CCA rating then press ‘Enter’ 7. Battery analysis will begin 8. During analysis you may be asked to confirm if battery has been re-charged: Select option 1 if battery was not re-charged before testing Select option 2 if battery was re-charged before testing 9.
-
Page 7: Earth Test
EARTH TEST Select this option to check there is a good earth between battery and vehicle chassis 1. When prompted move the black[-] clip from battery[-] to vehicle chassis 2. Press ‘Enter’ to begin analysis 3. Now move black clip back to battery[-] within 15 seconds 4. -
Page 8: Alternator Test
ALTERNATOR TEST Select this option to check alternator charging voltages are acceptable 1. Rev engine to 3000RPM, press enter then hold revs for 10 seconds 2. After analysis results are displayed: 1. Max allowable Charging Voltage 2. Min allowable Charging Voltage 3. -
Page 9: Indicator Functions
2. Insert CD into computer and open driver folder 3. Launch driver installer file 4. Follow instructions to install USB to Serial driver 5. Run setup file to install BLT700 software 6. Connect BLT700 to computer Unit will be detected and installed... -
Page 10: Software Operation
1. Select result to download then press USB key 2. Display will indicate ‘download mode’ is active 3. Launch BLT700 software by clicking desktop icon 4. Main screen will display as shown 5. Before proceeding confirm a COM port has automatically been selected e.g. COM-4 6. - Page 11 NOTES...
-
Page 12: Warranty Statement
WARRANTY STATEMENT Applicable only to product sold in Australia Brown & Watson International Pty Ltd of 1500 Ferntree Gully Road, Knoxfield, Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in its current catalogue (save and except for all bulbs and lenses whether made of glass or some other substance) will under normal use and service be free of failures in material and workmanship for a period of one (1) year (unless this period has been extended as indicated elsewhere) from the date of the original purchase by the consumer as marked on the invoice.
Need help?
Do you have a question about the BLT700 and is the answer not in the manual?
Questions and answers