Table of Contents
Advertisement
Quick Links
24-Port 10/100M Ethernet PoE Switch (af Version 15.4W)
• Introduction ...........................................................
• Power Over Ethernet (PoE) & Features ......................
• Unpacking and Installation ......... ..............................
• System Requirement....... .......................................
• Hardware Installation... ............. ...............................
• Front /Rear Panel /LED...........................................
• Connecting Ethernet Cable........................................
• Technical Specification..............................................
• Troubleshooting .......................................................
•FCC Warning:
This device has been tested and found to comply with the regulations for Class B digital equipment.Pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with users guide, may cause harmful interference to
radio communications. Operation of this devices in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his/her own expense.
•CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
•UL Warning:
1> Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater then room ambient. Therefore, Consideration should be given to
installing the equipment in an environment compatible with manufacturer's maximum rated ambient temperature
2> Reduced Air flow-installation of equipment in a rack should be such that the amount of air flow required for safe
operation of the equipment is not compromised.
3> Mechanical Loading- mounting of the equipment in the rack should be such as that a hazardous
Conditions is not achieved due to uneven mechanical loading.
IMPORTANT
This users guide contains information on the limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. Read the entire guide carefully
24-Port 10/100M Ethernet PoE Switch-AT
Quick Installation Guide
Table of Contents
Rev 1.0 04/10/2012 Page 1 / 8
Page 2
Page 2
Page 3
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Advertisement
Table of Contents
Related Manuals for OEM SST-MT-PSW24
Summary of Contents for OEM SST-MT-PSW24
- Page 1 Quick Installation Guide 24-Port 10/100M Ethernet PoE Switch (af Version 15.4W) Table of Contents • Introduction ………………………………………………….. Page 2 • Power Over Ethernet (PoE) & Features ……..………….. Page 2 • Unpacking and Installation ……… .……………………….. Page 3 • System Requirement……. .……………………………….. Page 3 •...
-
Page 2: Introduction
1. Introduction The 24-Ports10/100M Ethernet PoE Switch combines a high efficiency 24-ports 10/100Mbps Ethernet switch and a standard 802.3af 24-ports Power over Ethernet (PoE) capability. The 24-Ports 10/100M Ethernet PoE Switch incorporates an internal 48VDC power supply. Each of the PoE Ethernet ports can support 15.4 Watts of power as well as 10/100M data transmission over the Inter- connecting Ethernet interface such as Cat 5/ 5e /6 cables. -
Page 3: Unpacking And Installation
3. Unpacking and Installation Open the received cartons of the 24-ports 10/100 Ethernet PoE Switch and carefully unpack its contents. The cartons should Included following items: One 24-Ports 10/100M Ethernet PoE Switch. One AC power cord. Four rubber feet with adhesive backing. ... -
Page 4: Hardware Installation
5. Hardware Installation A: Connect the AC Power Cord to the 24-Ports 10/100M Ethernet PoE Switch and then to a power outlet. AC power Outlet AC Power Cord B: Connect a CAT-5, CAT-5e or CAT-6 RJ-45 network cable from the computer to an available Ethernet port on the 24-Ports 10/100M Ethernet PoE Switch. -
Page 5: Front Panel
6. Front Panel/LED/PoE Network Front Panel PoE ACT LED Power LED 10/100M PoE Port Act / Link LED 10/100M LED LED Display ＊ ●: Light ☼: Blinking Slowly O: Inactive : Blinking Fast Power LED LED on: Power ON / LED off: Power off. ●... -
Page 6: Connecting Ethernet Cable
6. Connecting Ethernet Cables Connecting Ethernet Cables INTERNET Ethernet Network Diagram : Data + 48VDC Data 100M Cat5/5e/6 cable Workstation Workstation Broadband Router 24 Port 10/100M PoE Device Ethernet PoE Switch PoE Touch Screen PoE Device PoE Device PoE Device PoE IP Camera PoE VoIP Phone PoE Wireless Access point... -
Page 7: Technical Specification
7. Technical Specifications Standard IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3x Full Duplex Flow Control IEEE 802.3af Power over Ethernet Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex) Network Cables 10BASE-T: 2-pair UTP Cat 3, 4, 5 up to 100 meters. -
Page 8: Troubleshooting
8. Troubleshooting 1> After connecting the Switch to a power outlet, the LEDs do not turn on. Check the connection of the power cord to the 24-Ports 10/100M Ethernet PoE Switch and the power outlet. Check that the power outlet is receiving power. 2>...