Advertisement
HMSOMP
Attachment
and
7.4
Changing the speed
(Fig.
2)
The saw has 2
speed
ranges:
.
To
operate
the
saw at a speed of
3800
rpm
(non-ferrous
metals),
set
the
switch
(42)
to position
l.
.
To operate
the
saw at a speed of
5000
rpm (wood), set
the
switch
(42)
to
posi-
tion
ll
7.5
Cross cut
90o
and
turntable
0'
(Fig.1,2,6,7)
ln
the
case of
cutting widths
up
to approx.
''100
mm it is possible
to
fix the
traction
function
of
the sawwith the
locking screw (23)
in
the rear
position
ln
this
position
the
machine
can
be
operated
in cross
cutting
mode
lf
the
cutting
width
is
over
100
mm
then
it is necessary
to
ensure that
the
locking screw (23) is loose and the
machine head (5)
can
move.
Caution!
For
90'
mitre cuts,
the
moveable fence (28) must be
fixed
in
the
inner
position.
r
Open
the
set screw (29)
on
the
moveable fence (28)
and
push
the
moveable
fence
(28) inwards.
.
Warning!
The
moveable fence (28) must be locked in a position far enough
from
the inner
position that
the distance
between
the fence
(28) and
the
saw
blade
(7)
is no more
than
5
mm
.
Before making
the cut,
checkthat
no
collision
could
occur
between
the
fence
(28) and
the
saw blade
(7).
.
Tighten
the
set screw (29) again
e
Move
the
machine head
(5)
to its
upper position.
.
Use
the
handle
(1)to
push back
the
machine head (5) and
fix
it
in
this position if
required (dependent
on
the cutting
width).
.
Place
the
piece
of
wood
to
be cut
at
the
fence
(18)
and
on
the
turntable
(16).
.
Lock
the
material with
the
clamping device
(8) on
the fixed
saw
table
(16)
to pre-
vent
the
material
from
moving during
the cutting
operation.
.
Push down
the
release lever
(3)
to
release
the
machine head
(5).
.
Press
the
ON/OFF
switch
(2)
to
start
the
motor
r
With
the
drag guide (23)
fixed
in
place:
use
the
handle
(1)to
move
the
machine head
(5)
steadily
and
with
light pressure
downwards until
the
saw blade
(7)
has completely cut through the
work
piece.
o With
the
drag guide (23)
not
fixed
in place:
pull
the
machine head (5)
all
the way to
the
front
Lower
the
handle
(1)
to
the
very
bottom by applying steady and light downward
pressure.
Now push
the
ma-
chine
head (5) slowly and steadily to
the very
back until
the
saw blade
(7)
has
completely
cut through the
work
piece.
r
When
the cutting operation
is
completed,
move
the
machine head (5)
backto
its
upper (home)
position
and release
the
ON/OFF
button
(2).
Caution!
The
machine executes an upward stroke
automatically
due to
the
re-
turn spring,
i.e. do not release
the
handle ('1)after completing
the cut;
instead
AFTER SALES SUPPORT
E
support@scheppach.com.aLt
MODEL:HMSOMP PRODUCT CODE:
53666
06/2017
21
t *'
1300
855
831
Advertisement
