RIDGID 916 Operator's Manual
  1. Manuals
  2. Brands
  3. RIDGID Manuals
  4. Power Tool
  5. 916
  6. Operator's manual

RIDGID 916 Operator's Manual

Portable roll groover
Hide thumbs Also See for 916:
Table of Contents

Advertisement

Quick Links

916
OPERATOR'S
MANUAL
• Français – p. 17
• Castellano – pág. 35
WARNING!
Read this Operator's Manual
carefully before using this tool.
Failure to understand and fol-
low the contents of this manu-
al may result in electrical
shock, fire and/or serious per-
sonal injury.
Find Quality Products Online at:
Portable Roll
Groover
GlobalTestSupply
www.
.com
sales@GlobalTestSupply.com

Advertisement

Table of Contents
loading

Related Manuals for RIDGID 916

Summary of Contents for RIDGID 916

  • Page 1 Portable Roll Groover OPERATOR’S MANUAL • Français – p. 17 • Castellano – pág. 35 WARNING! Read this Operator’s Manual carefully before using this tool. Failure to understand and fol- low the contents of this manu- al may result in electrical shock, fire and/or serious per- sonal injury.
  • Page 2 Installing 916 Roll Groover on 300 Power Drive ......................4 Installing Drive Bar Adapter For 1822-I, 535 or 300 Compact Threading Machines ..........5 Installing 916 Roll Groover on 535A, 535M, 1822-I or 300 Compact Threading Machines Mounted on 100, 150 or 200 Stands ..........................5 Installing 916 Roll Groover on 1822-I Threading Machine Mounted on 1406 Stand ..........5...
  • Page 3 916 Roll Groover For Models No. 300PD, 300 Compact, 535 or 1822-I Threading Machine GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...

  • Page 4: Work Area Safety

    916 Roll Groover General Safety Information • When operating a tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords WARNING! Read and understand all instructions. Failure are rated for outdoor use and reduce the risk of elec- to follow all instructions listed below may trical shock.

  • Page 5: Tool Use And Care

    916 Roll Groover Tool Use and Care Because the machine has high torque, the clothing itself can bind around your arm or other body • Do not use tool if switch does not turn it ON or parts with enough force to crush or break bones.

  • Page 6: Description

    150 and 200 Stands 45007 Roll Groover for 300 Compact Mounted on 15,0 The No. 916 Roll Groover is designed for specific use with 250 Stand (Also requires 67662 Adapter Bracket) the RIDGID No. 300 Power Drive, 300 Compact, 535M, Accessories 535A and 1822-I Threading Machines.

  • Page 7: Installing Drive Bar Adapter For 1822-I, 535 Or 300 Compact Threading Machines

    916 Roll Groover 3. Position 916 on far side carriage rail and lower onto roll housing is specifically designed for mounting of the rails of these machines. near side rail. (Figure 2) 1. Position carriage towards front chuck and swing car- 4.

  • Page 8: Machine Inspection

    Roll Groover until any problem Threading Machine has been repaired. 3. Place the 916 on the arms of the adapter. 6. Lubricate the Roll Groover if necessary according to the Maintenance Instructions. 4. Position base so that the drive bar feeds into the open chuck.

  • Page 9: Machine And Work Area Set-Up

    916 Roll Groover To avoid electrical shock and electrical fires, Machine and Work Area Set-Up WARNING never use an extension cord that is damaged or does not meet the following requirements. WARNING • The cord has a three-prong plug similar to shown in Electrical Safety section.

  • Page 10: Pipe Preparation

    916 Roll Groover Operating the 916 Roll Groover Failure to use two stands may result in WARNING unit tipping or the pipe falling. WARNING 2. Lift up on feed handle and place pipe on drive roll and Do not wear gloves or loose clothing when oper- pipe support.

  • Page 11: Adjusting Roll Groove Depth

    3. Tighten down depth adjustment screw the number of turns indicated in Chart B. (Figure 11) NOTE! Chart B indicates adjustment needed when using the 916’s standard roll set. See Chart D on Page 12 for special note on 1 AWWA grooving and 1″...

  • Page 12: Forming The Roll Groove

    4. After feed handle comes to rest on base of 916 Roll Groover allow two (2) complete pipe revolutions to even out groove depth. 5. Release foot switch and slip directional switch to OFF.

  • Page 13: Grooving Short Lengths Of Pipe

    916 Roll Groover 2. Push pivot pin back until stops. 3. Loosen depth adjustment screw. 4. Remove pivot pin. 5. Raise up groove roll housing. (Figure 15) 2° Figure 13 – Adjusting Pipe to Same Angle as Machine Grooving Short Lengths of Pipe 1.

  • Page 14: Roll Grooving Copper With No

    Only the following RIDGID products have WARNING been designed to function with the 916 Roll Groover. Forming Roll Groove Other accessories suitable for use with other tools may 1. Set adjustment screw for depth required. (See Chart become hazardous when used on this Roll Groover.

  • Page 15: Lubrication

    Machine any adjustments. should be taken to a RIDGID Independent Authorized Service Center or returned to the factory. All repairs made by Ridge service facilities are warranted against Lubrication defects in material and workmanship.

  • Page 16: Table I Standard Roll Groove Specification

    916 Roll Groover Table I. Standard Roll Groove Specifications NOTE! All Dimensions are in Inches. NOM. PIPE MIN. GASKET GROOVE GROOVE NOM. PIPE DIAMETER WALL SEAT WIDTH DIAMETER GROOVE DEPTH SIZE O.D. TOL. THK. +.015/-.030 +.030/-.015 O.D. TOL. 1.315 +.013 .065...

  • Page 17: Table Iii Troubleshooting

    Hand feed Grooving Roll into pipe faster. Driving Roll knurling plugged with metal or worn flat. Clean or replace Driving Roll. Power Drive does not supply minimum required Use RIDGID No. 300, 36 RPM Power Drive, 535 Groover will not rotate torque. or 1822-I Machine.

  • Page 18: Table Iv Copper Roll Groove Specifications

    916 Roll Groover Table IV. Copper Roll Groove Specifications NOTE! All Dimensions are in Inches. Nom. Tubing Outside Gasket Groove Groove Groove Min. Max. Size Diameter O.D. Seat Width Dia. Depth Allow. Allow. Inches +.03 +.00 Ref. Wall Flare Basic Tolerance ±.03...
  • Page 19 No other express warranty applies This FULL LIFETIME WARRANTY is the sole and exclusive warranty for RIDGID ® products. No employee, agent, dealer, or other person is authorized to alter this warranty or make any other warranty on behalf of the RIDGE TOOL COMPANY.

Table of Contents