Appendix A - Table Of Operating Parameters - Xpresense The Wag Owner's Manual

Appendix A - Table of Operating Parameters

Parameter/Screen Value Range
Name
PATCH 01 - 20
Off, Normal,
Offset, TYPE 3
Ped Type
- 6
0-100, 75-100,
Ped Zone 50-100, 25-75,
0-50, 0-25
FWD, REV
Ped Dir
MidiChan 01 - 16
000 – 127
Midi CC1
Off, FwdExp,
RevExp,
FwdMomSw,
CC1 Mode
RevMomSw,
FwdLatSw,
RevLatSw
0-100, 75-100,
CC1 Zone 50-100, 25-75,
0-50, 0-25
Midi CC2 000 - 127
Off, FwdExp,
RevExp,
FwdMomSw,
CC2 Mode
RevMomSw,
FwdLatSw,
RevLatSw
0-100, 75-100,
CC2 Zone 50-100, 25-75,
0-50, 0-25
Off, Low,
Exp damp
Medium, High
Off, On
Exp Hold
Low, Medium,
SW Sens
High
Off, FwdMom,
RevMom,
PrgMode
FwdLatch,
RevLatch
000 - 127
ProgChg1
000 - 127
ProgChg2
NAME 8 characters
Summary
Your configurations can be saved to 20 named patches
Applies to the Pedal Out jack. You can leave the cable connected and set Ped
Type to OFF to disable the interface.
Normal is for full range output. Some effects units don't respond to low values
from an expression pedal. Offset type compensates for this.
This determines the range of hand motion that controls your effects using the
Pedal Output.
See Chapter 4 Limiting the Expression Zone for further explanation.
Sets the direction of hand motion akin to toe up versus toe down for your Pedal
Output.
Sets the Midi Channel number for the current PATCH
st
Sets the 1 of 2 Continuous Controller Numbers (CC)
Sets the Mode of operation for CC1. Exp stands for expression mode versus
switch mode. In expression mode we send values 0 – 127 to provide expression
pedal functionality like volume swells. Fwd/Rev sets the direction of hand
motion. MomSw stands for Momentary Switch. LatSw stands for Latch Switch.
In switch mode we send midi values of 000 or 127 only. Effects units typically
turn an effect on with a value greater than 064 (mid range) and off if below 064.
See text for further explanation.
This determines the range of hand motion that controls your effects using Midi
CC1.
See text for further explanation.
nd
Sets the 2 of 2 Continuous Controller Numbers (CC)
Sets the Mode of operation for CC2. Exp stands for expression mode versus
switch mode. In expression mode we send values 0 – 127 to provide expression
pedal functionality like volume swells. Fwd/Rev sets the direction of hand
motion. MomSw stands for Momentary Switch. LatSw stands for Latch Switch.
In switch mode we send midi values of 000 or 127 only. Effects units typically
turn an effect on with a value greater than 064 (mid range) and off if below 064.
See text for further explanation.
This determines the range of hand motion that controls your effects using Midi
CC2.
See text for further explanation.
Damping slows the rate of change of the effects control. This is useful for
creating smooth volume swells. High is the slowest swell.
Holds the maximum effect value until the hand moves to the opposite end of the
zone. This allows you to swell an effect to maximum then hold that value while
you relax your hand.
For CC switch modes and Program Changes, this controls how sensitive the
switching is. With a lower sensitivity you will be less prone to accidental
switching but won't be able to toggle effects in rapid succession.
PrgMode pertains to the sending of Midi Program Change messages which are
used to change your effects unit patches. Reverse and Forward directions as
well as momentary and latch modes are selectable. You can also turn this
feature off.
If PrgMode is on this specifies the 1
equates to 1 of 2 effects patches.
If PrgMode is on this specifies the 2nd of 2 Program Change numbers which
equates to 1 of 2 effects patches.
Here is where you can name the Wag Base Unit Patch something meaningful.
st
of 2 Program Change numbers which
User's Manual
page 22