Resets All Functions Back To Default And Erases Any Remotes - Fortin E400 RF442W Quick Installation Manual

FUNCTION
MODE 1
FUNCTION
DEFAULT
18 Diesel Mode
19 Turbo timer
Engine supervision:
Tachless on crank and
-Tachless - -analog
20 supervision Tach Data-
tach- -Tach Data-
Link or analogic after
Link-
21 Start Attempts
22 —
RESET all programming
options by default.
23 Master RESET
(Retains already
programmed remote.)
Special
24
application
Auxiliary 1 Output 0.5 seconds &
25
Function --> LOCK disarm alarm
26 Hybrid mode Gas / Diesel vehicle
Auxiliary 2 Output- 0.5 seconds &
27
Function--> UNLOCK disarm alarm
Manual transmission
28 Neutral safety switch No application
Special Application
29 Alarm Duration 30 seconds
Ignition ON
30 Valet code
Valet button x3 times.
Special application
No special application
31 Programmable
Priority on function 2
output (+)
Dk.Blue (Ground out,
Configuration Pin17): Shut-down 1
Dk.Blue (Pin17) second after remote
32
Yellow/Red (Pin19) start run time.
wire ------------------
Yellow/Red (Pin19)=Arm
Activated by the remote
Manual transmission
33 starter remote.
function
See page 4.
34 Trunk output Pulse 0.5 seconds
Door unlock Special
35 No special application
application
Activation/
36 desactivation remote
Valet Mode
Security Remote car
37 starter No special application
Special application
System control by
38
OEM Remote
AUX1 CONTROLED
39
BY Temperature
LEGEND: FUNCTION BY DEFAULT
RESETS ALL FUNCTIONS BACK TO DEFAULT AND ERASES ANY REMOTES THAT HAVE BEEN PROGRAMMED.
STEP 1
Disarm the
system
(The
antenna led
Turn the
must not be
flashing, see
Ignition
enter/exit
ON.
valet mode
p.4).
MODE 2
Enable (20 seconds)
Delay between Ignition
Disable
power up and Starter
(crank).
Disable Run 2 minutes.
Tachless only.
( vehicles with
automatic transmission
only)
2 1
— —
—
Disable Application 1
0.5 seconds
Hybrid vehicle
0.5 seconds
Enable (see p.4)
60 seconds
Ignition ON
Valet button x3 times
and x1 times 3
seconds.
Special application - Function 2 (all option)
Enable at ground out,
disable with vehicle
ignition off
Dk.Blue (Ground out,
Pin17): Shut-down 3
seconds after remote
start run time.
Automatically activated
by hand-brake and Foot
Brake.
Pulse 2.5 seconds
Activate vehicle ignition
at unlock.
by remote : FUNCTION
LOCK + UNLOCK
—
or Valet button
Security ON: Shutdown
Engine if the door
is opened before
UNLOCK is pressed.
(Door trigger required).
Enable (Press 3x Lock
Disable to remote start) (Bypass
module required)
Enable : AUX1 activated
at +5 c when remote
o
Disable
started (see function
25)
STEP 2
OR
Press and hold the
valet switch or the
antenna button until
the Parking lights
turn ON, the horn/
siren will chirp.
MODE 3
Enable (10 seconds)
Delay between Ignition No delay between
power up and Starter Ignition power up and
(crank).
Run 4 minutes.
Start (crank) 8 sec
Analog Tach learning
(see p.4 for programming) vehicles with automatic
transmission only)
3
—
—
Application 2
10 sec latch or
until a button is pressed. until a button is pressed.
—
10 sec latch or until a 20 sec latch or until a
button is pressed. button is pressed.
For manual transmission vehicles equipped with neutral safety switch. DO NOT CUT THE LOOP.
Connect the auxiliary IN (Purple/White) to the neutral safety switch of the vehicle.
120 seconds
Ignition ON
Valet button x4 times Valet button x5 times
and x1 times 3 seconds. and x1 times 3 seconds.
not available.
White wire (5th relays): White wire (5th relays):
Trunk output(+) (+)Parking light output
Yellow/Red (Pin19) (Arm):
Shutdown after
Manual sequence
Cancel ready mode
completed by locking the
when trunk open.
doors
Unlock before trunk pulse Trunk Output at ignition
0.5sec
Activate vehicle ignition
and accessory at unlock.
-->
By Valet button only
—
— Alarm controled by OEM
—
STEP 3 STEP 4
OR
Press and
release the
X1
valet switch
or the antenna
button
23 times.
MODE 4
MODE 5
Enable
—
Starter (crank).
— —
Start (crank) 8 sec+
on tachless. ( Supervision by
Data-Link Tach (Data
interface required)
— —
— —
— —
Application 3 —
30 sec latch or
20 sec latch or
until a button is
pressed.
— —
30 sec latch or until a
button is pressed.
— —
Ignition ON
Ignition ON
Valet button x6
times and x1 times 3
seconds.
—
— —
—
—
only
— —
— —
— —
Enable (Press Lock,
Enable
Unlock Lock to remote
start) (Bypass module
Remote.
required)
— —
STEP 5
OR
Press and hold
Press and the valet switch
release or the antenna
the brake- button for 5 sec-
pedal onds. The Parking
once. lights will flash to
confirm.
MODE 6
—
—
Tach Data-Link
only (Data interface
required)
—
—
—
—
Latch until shutdown
—
—
—
Ignition ON
Valet button x7 times
and x1 times 3 sec.
—
—
—
—
—
—
—
—
—
STEP 6
Turn the Igni-
tion OFF to
exit program-
ming. The
Parking lights
will flash 4
times.