Advertisement
Blue Sky Energy – IPN Remote
TROUBLESHOOTING GUIDE
SYMPTOM
PROBABLE CAUSE
Completely dead, no
No battery power
display
Display turns on, but
Display not communicating
battery voltage
with charge controller
displays "– – –" rather
than a number
When charger turns
Output current display
on, current displays "–
selection set for an address not
– –" rather than a
present on the IPN network
number
When charger turns
Output current display
on, output current
selection set for wrong IPN
displays but the value
network address
seems incorrect
Bat– connected to PV– outside
charge controller
Voltage or current
Display or charge controller
value displayed seems
IPN network addressed has
to be stuck and does
changed
not change
Display not communicating
with charge controller
Specifications:
Power Consumption:
Display:
Communication and Cabling:
Operating Temperature:
Environmental Protection:
Weight:
Dimensions:
NB. As a part of our continuous improvement process specifications are subject to change without prior notice.
5 YEAR LIMITED WARRANTY
Blue Sky Energy, Inc. (hereinafter BSE), hereby warrants to the original consumer purchaser, that the product or any part thereof will be free from
defects due to defective workmanship or materials for a period of five (5) year subject to the conditions set fourth below. If within the coverage of
this limited warranty, BSE will repair or replace the product at BSE's discretion. The original consumer purchaser is responsible for all transportation
costs and insurance related to returning the product to BSE. BSE will cover standard ground transportation costs and insurance to return the
product to the original consumer within the continental US.
1. This limited warranty is extended to the original consumer purchaser of the product, and is not extended to any other party.
2. The limited warranty period commences on the date the product is sold to original consumer purchaser.
3. This limited warranty does not apply to any product or part thereof damaged by; a) alteration or disassembly, b) repair or service not rendered
by a BSE authorized repair facility, c) accident or abuse, d) corrosion, e) lightning or other act of God, or f) operation or installation contrary to
instructions pertaining to the product.
4. BSE's liability for any defective product or any part thereof shall be limited to the repair or replacement of the product, at BSE's discretion. BSE
will not be liable for any loss or damage to person or property, or any other damages, whether incidental, consequential or otherwise, caused by
any defect in the product or any part thereof. Some states do not allow exclusions or limitations of incidental or consequential damages, so the
above limitation may not apply to you.
5. Any implied warranty for merchantability or fitness for a particular purpose is limited in duration to the length of this warranty. Some states do
not allow exclusions or limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
6. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7 To obtain warranty repairs, contact BSE at 760-597-1642 or techsupport@blueskyenergyinc.com to obtain a Returned Goods Authorization (RGA)
number. Mark the outside of the package with the RGA number and return the product, postage prepaid and insured to the address below. The
consumer is responsible for all transportation costs and insurance related to returning the product to BSE, and for any shipping damage which
may void the warranty or increase the cost of repairs.
Blue Sky Energy | USA |
www.blueskyenergyinc.com
ITEMS TO EXAMINE OR CORRECT
Battery disconnected, overly discharged (<9V), or connected reverse polarity.
Battery powers unit, not PV.
Cable Faulty
Cable faulty
One charge controller only must be Master.
Poor or missing Bat – connections preventing communication
Configure display IPN network address to a charger present on the IPN network.
Configure display IPN network address DIP switch to read desired output current.
PV- & BAT- must be separate external to the unit for proper operation and cannot
connect to a common location. External connection prevents proper operation of
internal shunts and current measurement system.
Configure display IPN network address DIP switch to properly read output current of
a charger present on the IPN network
Intermittent display cable.
0.25W (typical standby), 1.0W backlit ON
3-Digit • 0.30" Low Power LED
Communication via 25' (7.6m)
RJ-11 4-pin telephone cable provided
2.9 x 2.45 x 0.9" (7.4 x 6.2 x 2.3 cm)
IPN Remote
-40°C – 40°C
IP00
0.017 lb. (42 g)
4
Advertisement
