Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SAMCOM FPBN10A
Summary of Contents for SAMCOM FPBN10A
- Page 1 User Manual SAMCOM FPBN10A...
- Page 2 INDEX User Security Information --------------------------------------------- 3 Maintenance and Cleaning Specification ------------------------------------------------------------ 11 1. Do not lift the transceiver directly by its antenna or external Feature ------------------------------------------------------------------- 11 microphone. Products Inspection --------------------------------------------------- 12 2. Dust the transceiver with an anti-pilling cloth to prevent bad contact. 3.
-
Page 3: User Security Information
User Security Information Troubleshooting Guide Handheld transceiver product safety and RF Problems Solutions radiation Battery may have been exhausted. Please update or recharging the battery. No Power Battery may not be installed correctly. Please Warning: Please read the manual carefully before remove the battery and reload it. - Page 4 Handheld Transceiver Safety Guidelines and QT & DQT tables Instruction To control the transceiver radiation, ensure to meet the general or Frequency of 50 groups QT (Hz) non-controlled environment radiation limitation standard, please operate following below procedures. Press PTT key when talking; and release PTT key when receiving. Because measured RF energy radiation will be generated when transmitting, so transmitting time should not exceed 50% of the using time.
- Page 5 Electromagnetic Interference / Electromagnetic Voice compression and expansion Compatibility This feature ensures the user in a variety of noisy environments can get a clear call. Set by the dealers in the channel through Remark: Electromagnetic Interference (EMI) occurs in nearly every programming software.
-
Page 6: Call Function
Medical devices Busy Channel Lockout Pacemaker This feature can prevent interferences to other walkie-talkies in the Advanced Medical Technology Association of the United States same channel. If the channel has been occupied, the press of the proposes holding the handheld transceiver with pacemakers should PTT button will bring a continuous "beep"... - Page 7 When the function is activated, the transceiver will check whether Operation warning there are calls on the channels that are set to be scanned. If a channel is tested to have signals on it, it will switch to this channel Car with an airbag in order to receive voices (which channels can be scanned is In the car with an airbag, do not put the transceiver...
- Page 8 The use of QT/DQT signaling sounds like giving you a personal Fuse and blasting areas channel, but as a matter of fact, your voices can still be heard by To avoid possible interference with blasting operations, others if their walkie-talkies adopt the same QT/DQT signaling as please switch off your transceiver when get close to you, or all of your walkie-talkies are simply without QT/DQT signaling.
- Page 9 Notes Volume Adjustment As this type of transceiver has an auto-squelch Antenna function, you will hear nothing when the power caution Not use the handheld transceiver with damaged antenna. is turned on and no call is received. You can It will cause skin mild burns if touch the damaged antenna. hold down the MONI button, and then turn the PWR/VOL knob clockwise to increase the volume, Battery...
- Page 10 Charging Equipment Notes Basic Function 1. Do not expose the charger to rain or snow. 2. Chargers by severe impact, or has been dropped, or subject to Operation Guide any damaged, do not use again. Buttons, Control Knobs, Switches and Indicators 3.
-
Page 11: Specification
Specifications and Parameters 2. Removal of the belt clip As for the removal of the belt clip, please refer to the installation steps and loose the screws in conterclockwise. General Specifications Installation/Removal of External Earphone or Microphone 1. Installation of the external earphone or Channel capacity 16 groups of memory channels CTCSS... -
Page 12: Products Inspection
Installation /Removal of Antenna Products Inspection 1. Installation of the antenna Welcome to use FPBN10A transceiver, and before using, we ⑴ Plug the screw-thread end of the anenna recommend you: into the socket at the top of the transceiver. Please open the giftbox carefully to confrim whether the items as ⑵... -
Page 13: Get Familiar With The Transceiver
3. Place the battery or the transceiver with battery on the charger. Get Familiar with the transceiver 4. Confirm that the battery contacts are well connected with the charger contacts, and the charge indicator light turns red, which represent the beginning of the charging operation. 5. -
Page 14: Battery Information
Extension of Battery life Battery Information 1. The performance of the battery will be reduced when the Battery on First Use temperature drops below 0 . In cold weather, it is advised to spare another battery for emergency. Please do not dispose the Since batteries leave factory without a fully charging, please charge cold batteries that can not work at low temperature but may be the new batteries before using. -
Page 15: Safety Training Information
SAFETY TRAINING INFORMATION Your SAMCOM radio generates RF electromagnetic en-ergy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, Warning and the ways to minimize such hazards. - Page 16 The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch. • ALWAYS use SAMCOM authorized accessories (antennas, batteries, belt clips, speaker/mics, etc). Use of unauthorized accessories can cause the FCC RF exposure compliance requirements to be exceeded.