1. Manuals
  2. Brands
  3. Weather Fast Manuals
  4. Tent
  5. 193-4879
  6. Assembly manual

Weather Fast 193-4879 Assembly Manual

General purpose shelter 10' x 10' x 8' (3 x 3 x 2.4 m)
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

General Purpose Shelter
TM
10' x 10' x 8' (3 x 3 x 2.4 m)
ASSEMBLY MANUAL
Model NO.: 193-4879
Tools required for assembly (not included)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 193-4879 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Weather Fast 193-4879

Summary of Contents for Weather Fast 193-4879

  • Page 1 General Purpose Shelter 10' x 10' x 8' (3 x 3 x 2.4 m) ASSEMBLY MANUAL Model NO.: 193-4879 Tools required for assembly (not included)
  • Page 2 TABLE OF CONTENTS Important safety instructions ...........................................2 Intended use ..............................................2 Parts list ................................................ 3 Assembly preparation ............................................ 4 Assembly ..............................................4 - 8 Maintenance and care ............................................9 Important notice ............................................12 IMPORTANT SAFETY INSTRUCTIONS WARNING! Read all safety instructions to reduce the risk of injury or death. This is a temporary structure and is not recommended as a permanent structure.
  • Page 3 PARTS LIST Description Illustration Upright Pole with Dimples center extension tube Bent Corner Leg Cross Rail Rafter Pole Bottom Cross Rail 3-Way Side Connector - Left 3-Way Side Connector - Right 4-Way Side Connector 3-Way Peak Connector 4-Way Peak Connector 4-Way Cross Rail Clamp 3-Way Cross Rail Clamp Anchor...

  • Page 4: Assembly Preparation

    ASSEMBLY PREPARATION ● Place all parts from the packaging box in a cleared area and arrange them on the ground in front of you. ● Remove all packaging materials and place them back in the box. Do not dispose the packaging materials until assembly is complete. ●...

  • Page 5: Assembly

    ASSEMBLY Step 1: Assembling roof frame Step 2: Attaching legs ● ● Lay out the roof frame parts as shown below (fig. 1). Assemble the legs (fig. 5). Leg type Connect to Upright pole (1), Corner legs Bent corner leg (3) Upright pole (1), Center Legs Center extension tube (2)

  • Page 6: Bent Corner Leg

    ASSEMBLY ● Four anchors (14) are provided to secure the shed. They are to be NOTE: installed around the bent corner legs (3) at each corner of the shed. ● Do not let the roof rest on the legs until all three legs ●...

  • Page 7: Cross Rail

    ASSEMBLY ● Raise and lower the handle two or three times to wind the strap onto the spindle (fig. 13). Strap inside the panel ● Insert the S-hook of the ratchet into the hole of the bent corner leg (3). Pump the ratchet handle repeatedly to tighten the strap (fig.

  • Page 8: Bottom Cross Rail

    ASSEMBLY Caution! ● Check and tighten the bottom cross rails (6) and ratchets (22) monthly to ensure that the roof tarp (19) is tight and safe. ● When disassembling the shed, press the spring-loaded bar and open the ratchet handle completely to pull out the strap (fig.
  • Page 9 IMPORTANT NOTICE IMPORTANT NOTICE: PLEASE READ CAREFULLY PRECAUTIONS WHICH MUST BE FOLLOWED: Keep all flame and heat sources away from this tent fabric. The tent fabric will burn if left in continuous contact with any flame source. DO NOT cook underneath or near canopy. DO NOT store or use flammable liquids underneath or near canopy.

Table of Contents

Save PDF