Hitachi SJ700 series Manual page 17

Code Function Name
A061 Frequency upper limit setting
A261 Frequency upper limit setting, 2nd motor
A062
Frequency lower limit setting
A262 Frequency lower limit setting, 2nd motor
A063 Jump (center) frequency setting 1
A064 Jump (hysteresis) frequency width setting 1
A065 Jump (center) frequency setting 2
A066
Jump (hysteresis) frequency width setting 2
A067 Jump (center) frequency setting 3
A068 Jump (hysteresis) frequency width setting 3
A069
Acceleration stop time frequency setting
A070 Acceleration stop time frequency setting
A071 PID function enable
A072 PID proportional gain
A073 PID integral time constant
A074
PID derivative gain
A075 PV scale conversion
A076
PV source setting
A077 Output of inverted PID deviation
A078 PID variation range
A079 PID feed forward selection
A081 AVR function select
A082
AVR voltage select
A085 Operation mode selection
A086 Energy saving mode tuning
A092 Acceleration (2) time setting
A292 Acceleration (2) time setting, 2nd motor
A392
Acceleration (2) time setting, 3rd motor
A093 Deceleration (2) time setting
A293 Deceleration (2) time setting, 2nd motor
A393
Deceleration (2) time setting, 3rd motor
A094 Select method to switch to Acc2/Dec2 proÞ le
Select method to switch to Acc2/Dec2,
A294
2nd motor
A095
Acc1 to Acc2 frequency transition point
Acc1 to Acc2 frequency transition point,
A295
2nd motor
A096 Dec1 to Dec2 frequency transition point
Dec1 to Dec2 frequency transition point,
A296
2nd motor
A097 Acceleration curve selection
A098 Deceleration curve selection
A101
OI-L input active range start frequency
A102 OI-L input active range end frequency
A103 OI-L input active range start current
A104 OI-L input active range end current
A105 OI-L input start frequency enable
A111
O2-L input active range start frequency
A112 O2-L input active range end frequency
A113 O2-L input active range start voltage
A114 O2-L input active range end voltage
A131 Acceleration curve constants setting
A132
Deceleration curve constants setting
A141 Operation-target frequency selection 1
A142 Operation-target frequency selection 2
A143 Operator selection
A145 Frequency to be added
A146 Sign of the frequency to be added
A150
EL-S-curve acceleration ratio 1
A151 EL-S-curve acceleration ratio 2
A152 EL-S-curve deceleration ratio 1
A153 EL-S-curve deceleration ratio 2
(*1) 4000HF:0.00 to 99.99,100.0 to 120.0 (Hz) (*2) -120. to -100., -99.9 to 0.00 to 99.99 ,100.0 to 120.0 (Hz)
(*3) SJ700D (VT mode):00 (Normal operation), 01 (Energy saving operation)
Monitored data or setting
0.00 or "1st minimum frequency limit" to "maximum frequency" (Hz)
0.00 or "2nd minimum frequency limit" to "maximum frequency, 2nd motor" (Hz)
0.00 or "start frequency" to "maximum frequency limit" (Hz)
0.00 or "start frequency" to "maximum frequency, 2nd motor limit" (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)
0.00 to 10.00 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)
0.00 to 10.00 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)
0.00 to 10.00 (Hz)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*1)
0.0 to 60.0 (s)
00 (disabling), 01 (enabling), 02 (enabling inverted-data output)
0.2 to 5.0
0.0 to 999.9, 1000. to 3600.0 (s)
0.00 to 99.99, 100.0 (s)
0.01 to 99.99
00 (input via OI), 01 (input via O), 02 (external communication),
03 (pulse-string frequency input), 10 (operation result output)
00 (OFF), 01 (ON)
0.0 to 100.0 (%)
00 (disabled), 01 (O input), 02 (OI input), 03 (O2 input)
00 (always on), 01 (always o ), 02 (o during deceleration)
200 V class: 200, 215, 220, 230, 240 (V) 400 V class: 380, 400, 415, 440, 460, 480 (V)
00 (Normal operation)/ 01 (Energy-saving operation)/ 02 (Fuzzy operation) (*3)
0.1 to 100.0
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
00 (switching by 2CH terminal), 01 (switching by setting),
02 (switching only when rotation is reversed)
00 (switching by 2CH terminal), 01 (switching by setting),
02 (switching only when rotation is reversed)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
00 (linear), 01 (S curve), 02 (U curve), 03 (inverted-U curve), 04 (EL-S curve)
00 (linear), 01 (S curve), 02 (U curve), 03 (inverted-U curve), 04 (EL-S curve)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
0. to "[OI]-[L] input active range end current" (%)
"[OI]-[L] input active range start current" to 100. (%)
00 (external start frequency), 1 (0 Hz)
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz) (*3)
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz) (*3)
-100. to 02 end-frequency rate (%)
"02 start-frequency rate" to 100. (%)
01 (smallest swelling) to 10 (largest swelling)
01 (smallest swelling) to 10 (largest swelling)
00 (digital operator), 01 (keypad potentiometer), 02 (input via O), 03 (input via OI),
04 (external communication), 05 (option 1), 06 (option 2), 07 (pulse-string frequency input)
00 (digital operator), 01 (keypad potentiometer), 02 (input via O), 03 (input via OI),
04 (external communication), 05 (option 1), 06 (option 2), 07 (pulse-string frequency input)
00 (addition: A141 + A142), 01 (subtraction: A141 - A142), 02 (multiplication: A141 x A142)
0.00 to 99.99, 100.0 to 400.0 (Hz) (*2)
00 (frequency command + A145), 01 (frequency command - A145)
0. to 50. (%)
0. to 50. (%)
0. to 50. (%)
0. to 50. (%)
［⃝ = Allowed
Default Setting
SJ700/SJ700D(CTmode) SJ700B
(allowed or not)
-FE -FU -F -F -FU
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.50 0.50 0.50 0.50 0.50
0.00 0.00 0.00 0.00 0.00
0.50 0.50 0.50 0.50 0.50
0.00 0.00 0.00 0.00 0.00
0.50 0.50 0.50 0.50 0.50
0.00 0.00 0.00 0.00 0.00
0.0 0.0 0.0 0.0 0.0
00 00 00 00 00
1.0 1.0 1.0 1.0 1.0
1.0 1.0 1.0 1.0 1.0
0.00 0.00 0.00 0.00 0.00
1.00 1.00 1.00 1.00 1.00
00 00 00 00 00
00 00 00 00 00
0.0 0.0 0.0 0.0 0.0
00 00 00 00 00
00 00 02 00 02
400 230/460 200/400 200/400 200/400
00 00 00 00 00
50.0 50.0 50.0 50.0 50.0
15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00 15.00 15.00
15.00 15.00 15.00 15.00 15.00
00 00 00 00 00
00 00 00 00 00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
00 00 00 00 00
00 00 00 00 00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
20. 20. 20. 20. 20.
100. 100. 100. 100. 100.
00 00 00 00 00
0.00 0.00 0.00 0.00 0.00
0.00 0.00 0.00 0.00 0.00
-100. -100. -100. -100. -100.
100. 100. 100. 100. 100.
02 02 02 02 02
02 02 02 02 02
02 02 02 02 02
03 03 03 03 03
00 00 00 00 00
0.00 0.00 0.00 0.00 0.00
00 00 00 00 00
25. 25. 25. 25. 25.
25. 25. 25. 25. 25.
25. 25. 25. 25. 25.
25. 25. 25. 25. 25.
×
= Not permitted］
Setting Change
during during
operation operation
(allowed or not)
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
○ ○
○ ○
○ ○
× ○
× ○
× ○
× ○
× ○
×
×
×
×
×
×
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
× ×
× ×
× ×
× ×
× ×
× ×
× ×
× ×
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ○
× ×
× ×
× ×
× ×
16