Advertisement
How to disassmble
① Remove Caps.
② Remove Hole Pins as shown.
③ Slide Panel forward to separate from
Coupling Rod as shown.
(Do not force by pulling or twisting
Coupling Rod.)
Cautions!
l Take care that product does not collapse while disassembling.
l Leave Door locked when assembling Door Panel.
How to open and close the Gate Door
l Grip and lift the Upper Gate Lock so that
the Gate Door is opened by releasing
Upper and Lower Gate Locks.
l The product is designed to lock automatically
when closed. If too much or too little force is
used when closing, the Gate Door may not
lock.
How to Adjust Upper Gate Lock
Please adjust the Upper Gate Lock to lock the
gate properly when the Gate Door is closed.
1.The adjusting Screw is located underneath
the Upper Gate Lock. Using a phillips
screwdriver, loosen the Screw but do not
remove it completely.
2.Using a phillips screwdriver, slide the Upper
Gate Lock until there is no gap between
Upper Gate Lock and Upper Lock Receiver.
3.Tighten the Screw securely in place. The Gate
Door should now lock properly.
How to clean
lWipe off this product with washing cloth after squeezed firmly using a mild detergent and water. Do not use a scrub brush
and/or a polishing powder as these may cause scratched, rust and discolor to the product.
lWhen using creosol or other disinfectants, make sure to dilute them, otherwise damage to the wooden finish or discoloration
may occur.
lDo not use harsh chemicals such as thinner, benzene or alcohol as these may cause damage/discoloration to the finish.
lAfter cleaning, wipe dry with soft cloth or place in a shaded area to air dry; do not place product in direct sunlight.
Specifications
UPC/JAN
803840 / 4973655
94196-6
98754-4
94170-6
50061-3
94198-0
98755-1
94199-7
98756-8
94171-3
50071-2
94188-1
50070-5
94901-6
98757-5
94936-8
50591-5
※
※
94937-5
50601-1
lPlease note that product specifications and design may change without prior notice for the purpose of quality improvement.
lThere may be coating cracks at some joints and each product may experience different coloration of the wood grain as frames are made of natural wood.
lIf you find something wrong with this product, please let us know. Thank you!
Shop for other Pet Supplies on our website.
Dimension Width x Depth x Height (inches)
Model
Pet Pen
L4
31.9×36.2×20"
O4
31.9×36.2×31.5"
H4
31.9×36.2×35.8"
Wire
L6
Slat
31.9×68.9×20"
Model
O6
31.9×68.9×31.5"
O6
31.9×68.9×31.5"
H6
31.9×68.9×35.8"
Mesh
H4
31.9×36.2×35.8"
Panel
H6
31.9×68.9×35.8"
Model
①
Upper Gate Lock
Upper Gate Lock
Gap
Screw
1. Loosen the Screw
Gate
64.6∼68.7×31.7∼33.7×20"
64.6∼68.7×31.7∼33.7×31.5"
64.6∼68.7×31.7∼33.7×35.8"
129.9∼134.4×31.7∼33.7×20"
129.9∼134.4×31.7∼33.7×31.5" 135.8×29.1×31.5"
129.9∼134.4×31.7∼33.7×31.5" 135.8×29.1×31.5"
129.9∼134.4×31.7∼33.7×35.8" 138.2×24.8×35.8"
64.6∼68.7×31.7∼33.7×35.8"
129.9∼134.4×31.7∼33.7×35.8" 138.2×24.8×35.8"
②
Upper Lock Receiver
2. Slide the Upper
Gate Lock
3. Tighten the Screw
Room Divider
Wooden Frame: Natural wood
91.7×24.8×20"
Metal Part: Steel
91.7×29.1×31.5"
Door Plastic Part: Polypropylene
91.7×24.8×35.8"
Cap: Nylon
(Only for Wire Slat Model)
138.2×24.8×20"
Wire Slat: Steel
Rubber Skid: Elastomer
(Only for Mesh Panel Model)
Mesh Panel: Steel
Rubber Skid: Silicon
91.7×24.8×35.8"
③
Lower Gate Lock
No gap
Material
Advertisement
