General Cleaning Instructions; General Operating Instructions; Directions For The Display Panel; Setting Temperature - NuWave Precision Owner's Manual

GENERAL CLEANING INSTRUCTIONS:

• Unplug the unit before cleaning.
• Clean after each use.
• Always make sure the unit is completely cooled before cleaning.
• The top surface can be cleaned by wiping it with a damp cloth.
• Remove the power plug prior to cleaning the induction cooktop. Do not
use any caustic cleaning agents and make sure that water does not
penetrate inside the induction cooktop.
• Never immerse the induction cooktop, its cables or the plug into water
or other liquids.
• Wipe off the glass cooktop with a damp cloth or use a mild, non-abrasive
soap solution. Make sure the unit is cooled completely before cleaning.
• Wipe off the casing and the operating panel with a soft cloth or a mild
detergent.
• Do not use any oil based cleansing products as this can damage the
plastic parts or the casing/operating panel.
• Do not use any flammable, acidic or alkaline materials or substances near
the induction cooktop, as this may reduce the service life of the induction
cooktop and pose a fire risk when the induction cooktop is turned on.
• In order to keep your cooktop looking new, make sure that the bottom of your
cookware does not scrape the glass surface, although a scratched surface
will not impair the use of the induction cooktop.
• Make sure to properly clean the unit before storing it in a cool, dry place.
IMPORTANT TIPS:
1. Check the power outlet for proper operation. Do not operate the unit with
other major appliances in the same power outlet. Check power level if the
unit cooks too slowly.
2. Check to see if electrical plug is properly plugged into the outlet.
3. Always turn off and unplug the unit before wiping down.

GENERAL OPERATING INSTRUCTIONS:

• Place the cooktop on a stable, level and non-metallic surface.
• Never place the cooktop on a flammable surface (e.g. table cloth, carpet, etc.).
• Do not block the ventilation slots of the induction cooktop. This may overheat
the cooktop. Keep a minimum distance of 3-5 inches from walls and other
objects, appliances, etc.
• Do not place the induction cooktop next to devices or objects that react
sensitively to magnetic fields (e.g. radios, TVs, video recorders, etc.).
• Do not place the induction cooktop next to open fires, heaters or other
sources of heat.
• Make sure that the power cable is not damaged or compressed beneath the
induction cooktop.
• Make sure that the power cable does not come into contact with sharp edges
and/or hot surfaces.
• Prior to connecting the induction cooktop, check whether the voltage indicated
in this manual corresponds to the voltage supply in your home. A wrong
connection may lead to damage to the induction cooktop and possible injury to
persons.
• The cooktop's surface is made of temperature-resistant glass. In the event
that damage to the unit is observed, even if it is only a small crack on the glass
surface, disconnect the induction cooktop from the power supply immediately.
7 • THE NUWAVE PRECISION COMPLETE COOKBOOK

DIRECTIONS FOR THE DISPLAY PANEL

Display
Decrease
Prog Time
Low - Max / Sear
EASY START:
Precision is preset to cook at High (425 degrees F) for 45 minutes.
To start cooking, press "Start" button, make sure the pot is on the surface.
If cooking at any other power level other than "High", you would need to press
"Low" to "Max/Sear" or press the "-" or "+" to increase or decrease temperature
in 10 F degree increments. See the Panel Display Chart on the bottom of this
page.
CONTROL PANEL ON DISPLAY PANEL:
"0" should appear when the program is clear or power is on.
WHEN YOU START COOKING:
Set your temperature and time, then press "Start" to begin cooking. The oven
will automatically stop cooking when the time has expired and will beep to alert
you that it has stopped. The display will always show the temperature during
the cooking cycle. If you wish to see the time count down, press "Time" and the
time will show until the cycle or stage is complete.

SETTING TEMPERATURE:

This appliance is preset to cook at High (425 degrees F). To set the
temperature, press temperature key "Low" - "Max/Sear", then press "Start".
The temperature range will show on the display panel. To raise or lower the
temperature, press the "+" button or "-" until desired temperature is shown in
display panel. Refer to chart below for preset temperatures.
The minimum temperature is 100°F and the maximum temperature is 450°F.
The "+" and "-" will increase or decrease the temperature in 10°F increments.
Press Button Range Temperature / Panel Display
Low 100°F (37°C)
Med Low 175°F (79°C)
Med 275°F (135°C)
Med High 375°F (191°C)
High 425°F (218°C)
Max/Sear 450°F (232°C)
LCD
Increase Start
Pause / Clear
Examples
/ 100F Warm
/ 175F Simmer
/ 275F Steam
/ 375F Stir/Deep Fry
/ 425F Boil/Saute
/ SEAr Sear
OWNER'S MANUAL • 8