Related Manuals for Teledyne 913
Summary of Contents for Teledyne 913
- Page 1 Power Products Guide Installation and Operation Guide Part #60-9003-092 Copyright © 2002. All rights reserved, Teledyne Isco, Inc. Revision T, November 2017...
- Page 3 Teledyne Isco recommends that you read this manual completely before placing the equipment in service. Although Teledyne Isco designs reliability into all equipment, there is always the possibility of a malfunction. This manual may help in diagnosing and repairing the malfunction.
-
Page 5: Table Of Contents
4.3 Model 963 Battery Charger ......... . . 4-2 4.4 Model 913 and 923 High Capacity Power Packs ......4-3 4.5 Models 914 and 924 Battery-Backed Power Packs . - Page 6 4-3 Model 913 High Capacity Power Pack ........
-
Page 7: Section 1 Introduction
Products that have their own manuals are discussed only briefly here. 1.2 Model Numbers Teledyne Isco has assigned model numbers to most power products. The three-digit model numbers start with 9XX. • The 910 series are 120-volt high capacity power packs and battery-backed power packs: ·... -
Page 8: Compatibility Of Batteries And Chargers
Power Products Guide Section 1 Introduction · Model 963–Desktop Single Station Lead-Acid Battery Charger - for lead-acid batteries, 120 or 230 · Model 965–Five Station Battery Charger - for one to five lead-acid or nickel-cadmium batteries, 120 or 240 VAC. 1.3 Compatibility of Refer to Table 1-1 below to check the compatibility of various Isco batteries and chargers. -
Page 9: Section 2 Batteries
Power Products Guide Section 2 Batteries 2.1 General Information Teledyne Isco offers two different batteries for use with its equipment. Both batteries fit inside of or on top of Isco equipment and fasten to the equipment with rubber draw catches. Both have advantages and disadvantages. The choice is ultimately up to you. -
Page 10: Battery Ratings (Ampere-Hours)
“C” is useful for determining how long you can power an Isco instrument from a particular battery. Teledyne Isco provides average current consumption figures for most equipment. You can use these figures as a rough estimate to calculate the... -
Page 11: Determining Life Expectancy Of Charge
The important issue here is to be aware that current con- sumption for your equipment will depend largely on your pro- gramming choices. Teledyne Isco cannot guarantee a specific current consumption for a product, because programming flexi- bility has so great an effect on it. You may have to experiment for some time to match the battery life expectancy with your pro- gramming choices. -
Page 12: Model 934 Nickel-Cadmium Battery
Power Products Guide Section 2 Batteries current through the cell, in effect, charging it backwards. This amounts to the electrical reversal of the two poles of the cell, and can ruin either type of battery. In nickel-cadmium batteries, cell reversal causes gas generation, and that may force the vents to open. -
Page 13: Charging
Power Products Guide Section 2 Batteries Figure 2-1 Model 934 Nickel-Cadmium Battery The battery has an internal fuse, rated at approximately 50 amperes, to prevent the possibility of fire or burns in the event of a short circuit. If the internal fuse link blows, you will have to return the battery to the factory for repair. -
Page 14: Charging Temperature
Power Products Guide Section 2 Batteries confinement from the cells or enclosure. The gases may be explosive and they can also be irritating to smell. All rechargeable batteries, whether nickel-cadmium or lead-acid, have one-way safety vents that open to relieve inter- nal pressure generated by overcharging or very heavy dis- charge. -
Page 15: Effects Of Overcharging The Battery
If the charger delivers more than 600 mA, Teledyne Isco recommends you do not use it. If it delivers less than 100 mA, the charging period becomes too long. -
Page 16: Servicing The Nickel-Cadmium Battery
If you are not familiar with these procedures, or are uncomfortable doing them, return the battery to Teledyne Isco for repair. If the fuse is all right and only the cable needs replacing, Teledyne Isco suggests making the repair after the battery has been discharged. - Page 17 Power Products Guide Section 2 Batteries Figure 2-2 Model 946 Lead-Acid Battery T h e l e a d - a c i d b a t t e r y o f f e r s h i g h e r c a p a c i t y t h a n t h e nickel-cadmium battery at a lower price.
-
Page 18: Charging Lead-Acid Batteries
Power Products Guide Section 2 Batteries swell and crack the case. This will ruin the battery and could also release toxic substances. • You can easily damage a gelled-electrolyte lead-acid battery by overcharging. By necessity, the amount of water in a gelled-electrolyte battery is quite limited. -
Page 19: Using Other Battery Chargers
2.4 Model 948 Lead-Acid In addition to the Model 946 and 947 Lead-Acid Batteries, Teledyne Isco offers a much larger battery, the Model 948. This Battery battery, which resembles an automotive battery, has a capacity of 45 ampere-hours, eight and a half times the capacity of Models 946 and 947. -
Page 20: Model 948 Battery
Figure 2-3 Model 948 Battery Teledyne Isco offers the battery, a convenient carrying case (rec- ommended) and a six-foot connect cable. The cable terminates in a two-pin M/S connector suitable for attachment to Isco sam- plers and flow meters. -
Page 21: Use Of Other Types Of Batteries
Power Products Guide Section 2 Batteries Chargers for smaller Isco batteries are not recommended for the Model 948, as they will take too long to recharge the battery. Note the nylon webbed strap around the battery case. Its purpose is to keep the case closed, not a carrying handle. -
Page 22: Maintenance And Charging
Power Products Guide Section 2 Batteries meters, pumps, and other equipment. These batteries are quite large compared to the standard Isco battery packs, so you must mount them separately from the equipment they are powering. CAUTION Mount wet cell batteries securely so they cannot tip over. This is important because the acid in the electrolyte is both corro- sive and toxic. - Page 23 Power Products Guide Section 2 Batteries fused. Enough current can flow to burn up the wires quickly. It is possible for battery cables shorted together to “weld.” This will cause almost immediate melting and burning of the wire insu- lation until the wire melts open at some point. WARNING Fire, severe burns to the hands, and the release of toxic fumes are all possible from such a mishap.
-
Page 24: Section 3 Batteries For Flow Loggers
Power Products Guide Section 3 Batteries for Flow Loggers 3.1 Internally Mounted The flow loggers contain internal mounting provisions for two Batteries different types of batteries. The first type is a pair of standard 6-volt alkaline “lantern” batteries. The second is a 6.5 Ah, 12-volt lead-acid battery, similar to the standard Isco Lead-Acid Battery, but with a different cable and connector. -
Page 25: Flow Loggers - External Power Sources
Positioning is not critical, because the contact strips in the bottom of the compartment are laid out for universal acceptance. These batteries are available from Teledyne Isco or from any local hardware, sporting goods, or electronics wholesaler. Note that this type of battery is not rechargeable, despite occa- sional claims to the contrary. -
Page 26: Section 4 Isco Battery Chargers And Power Packs
Power Products Guide Section 4 Isco Battery Chargers and Power Packs 4.1 Isco Chargers and Teledyne Isco offers several battery chargers and two different power packs for use with all Isco products. You can use the power Power Packs packs instead of the nickel-cadmium or lead-acid batteries to power the samplers, flow meters, or other equipment. -
Page 27: Model 963 Battery Charger
Power Products Guide Section 4 Isco Battery Chargers and Power Packs 4.3 Model 963 Battery This charger is designed to charge the Model 946 and 947 Lead-Acid Batteries. It is capable of running from 120/230 VAC Charger at 50/60 Hz. The Model 963 Battery Charger is listed by UL (Underwriters Laboratories) and is CE marked. -
Page 28: Model 913 And 923 High Capacity Power Packs
12 VDC at 5 Packs amperes. The charger’s output is regulated at 400 mA, suitable for nickel-cadmium batteries. The Model 913 is for 120 volts and Model 923 is for 230 volts. Figure 4-3 Model 913 High Capacity Power Pack... -
Page 29: Models 914 And 924 Battery-Backed Power Packs
Power Products Guide Section 4 Isco Battery Chargers and Power Packs 4.5 Models 914 and 924 The Battery-Backed Power Packs contain a 5-ampere switching regulator and a 1.2 ampere-hour, 12-volt nickel-cadmium battery Battery-Backed Power as a backup power source. There is no external charging circuit; Packs the charger is connected internally to the standby battery. -
Page 30: Model 965 Five-Station Battery Charger
Generally the batteries (either type) will attain full charge within 15 to 18 hours. Occasional or slight overcharging of the batteries will not hurt them, but Teledyne Isco recommends that you avoid frequent or prolonged overcharging. Each Five-Station Battery Charger comes with its own manual. Operating instruc- tions are provided in this manual, as well as other information, so it is not repeated here. -
Page 31: Solar Panel Charger
Section 4 Isco Battery Chargers and Power Packs 4.7 Solar Panel Charger Teledyne Isco offers the Solar Panel Battery Charger to make possible operation of battery-powered equipment in very remote locations where AC power is not available to run a standard charger or power pack. -
Page 32: Appendix A Power Product Part Numbers
Power Products Guide Appendix A Power Product Part Numbers A.1 Part Numbers This appendix contains a list of Isco power products and their corresponding part numbers. Teledyne Isco, Inc. Customer Service Department P.O. Box 82531 Lincoln, NE 68501 USA Phone: (800) 228-4373... - Page 33 2191EX Zone 0 battery module only 68-2000-022 SLA2191EX Rechargeable for 2191EX Zone 0 battery module only 68-2000-023 Lead-Acid Battery Pack 913 High Capacity Power Pack 120 V, charges 934 ni-cad 60-1684-088 923 High Capacity Power Pack 230 V, charges 934 ni-cad 60-3004-190...
-
Page 34: Appendix B Material Safety Data Sheets
This appendix to the manual provides Material Safety Data Sheets for Isco Power Products. Teledyne Isco cannot guarantee the accuracy of the data. Specific questions regarding the use and handling of the products should be directed to the manufacturer listed on the MSDS. - Page 35 Power Products Guide Appendix B Material Safety Data Sheets...
- Page 36 Power Products Guide Appendix B Material Safety Data Sheets Page 2 of 6 Cadmium: Melting point (°F): 610 Boiling point (°F): 1,407 % Volatile by Volume: Vapor Pressure (mm Hg): Evaporation Rate: Vapor Density (Air =1): Specific Gravity (H O): 8.65 @77¡F Solubility in Water: Insoluble Appearance and Odor: Silver-white, blue-tinged, lustrous metal Cadmium...
- Page 37 Power Products Guide Appendix B Material Safety Data Sheets Page 3 of 6 Section IV - Fire and Explosion Hazard Data Flash point: NA Lower Explosive Limit: NA Upper Explosive Limit: NA Extinguishing Media: Any class of extinguishing medium may be used on the batteries or their packing material. Special Fire Fighting Procedures: Exposure to temperatures of above 212°F can cause evaporation of the liquid content of the potassium hydroxide electrolyte resulting in the rupture of the cell.
- Page 38 Power Products Guide Appendix B Material Safety Data Sheets Page 4 of 6 Other Effects of Repeated (Chronic) Exposure: Repeated overexposures to cadmium may result in lung cancer; lung, kidney, and liver dysfunction; skeletal disease (e.g., osteoporosis) and reproductive toxicity. Chronic overexposure to nickel may result in cancer; dermal contact may result in dermatitis in sensitive individuals.
- Page 39 Power Products Guide Appendix B Material Safety Data Sheets Page 5 of 6 Section VIII - Safe Handling and Use (Personal Protective Equipment) Ventilation Requirements: Not required under normal use. Respiratory Protection: Not required under normal use. Eye Protection: Not required under normal use. Gloves: Not required under normal use.
- Page 40 Power Products Guide Appendix B Material Safety Data Sheets...
- Page 41 Power Products Guide Appendix B Material Safety Data Sheets HMIS Hazard Rating HEALTH Material Safety Data Sheet FLAMMABILITY 24-HOUR EMERGENCY CONTACT REACTIVITY (336) 650-7245/7257 CHEMTREC (800) 424-9300 0 Minimal Hazard 1 Slight Hazard 2 Moderate Hazard 3 Serious Hazard 4 Severe Hazard PREPARED BY: A.L.
- Page 42 Power Products Guide Appendix B Material Safety Data Sheets SECTION 4 – PHYSICAL HAZARDS Stability Stable Conditions to Avoid Avoid overcharging. Do not allow smoking, sparks, or open flame near batteries while charging. Incompatibility (Materials to Avoid) Keep battery case away from strong oxidizers. Hazardous Decomposition Products An explosive hydrogen/oxygen mixture within the battery may occur during charging.
- Page 43 Power Products Guide Appendix B Material Safety Data Sheets B-10...
- Page 44 Power Products Guide Appendix B Material Safety Data Sheets B-11...
- Page 45 Warranty Name and amount of Hazardous Substances or Elements in the product Hazardous Substances or Elements Component Name (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) Name and amount of Hazardous Substances or Elements in the product O: Represent the concentration of the hazardous substance in this component’s any homogeneous pieces is lower than the ST/ standard limitation.
- Page 47 Name and amount of Hazardous Substances or Elements in the product Hazardous Substances or Elements Component Name (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) Name and amount of Hazardous Substances or Elements in the product O: Represent the concentration of the hazardous substance in this component’s any homogeneous pieces is lower than the ST/ standard limitation.
- Page 49 Name and amount of Hazardous Substances or Elements in the product Hazardous Substances or Elements Component Name (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) Name and amount of Hazardous Substances or Elements in the product O: Represent the concentration of the hazardous substance in this component’s any homogeneous pieces is lower than the ST/ standard limitation.
- Page 51 The warrantor is Teledyne Isco, 4700 Superior, Lincoln, NE 68504, U.S.A. *This warranty applies to the USA and countries where Teledyne Isco does not have an authorized dealer. Customers in countries outside the USA, where Teledyne Isco has an authorized dealer, should contact their Teledyne Isco dealer for warranty service.
-
Page 53: Model 934 Nickel-Cadmium Battery
4-3 Model 913 High Capacity Power Pack ........ -
Page 54: Battery/Charger Compatibility 2
Battery/Charger Compatibility 2 Power Product Part Numbers and Compatibility 2...