Shure 526T Series II Wiring Manual page 5

BLACK Notes
A-
BLUE
MDU-6000
MCE6510, AUDIO CKT GND NC XMTR CKT CKT GND NC
TRE6500,
MCR-6450,
TRC-6448,
RED
(red)
ATLAS
2101215, 210x1215~
TRR-64541A
CBF-2179
CBH-2265
CBU-2068
CBR-2175
B&K I DYNASCAN
Cobra 46XLR,
86XLR, 132XLR,
135XLR
Cobra 47XLR,
50XLR, 55XLR
Cobra 6
Cobra 19, 21, 29,
21X, 85; Cam 89,
21XLR, 29XLR,
32XLR, 89XLR,
77X
Cobra 20, 24
Cobra 23, 27, V
Cobra 25
Cobra 28, 28A, 130,
131, 132, 132A,
135, 139, 880,
32XLR, 139XLR,
45XLR
Cobra 134, 138,
138A
Cam 88, Cobra 98
Cobra 138XLR
19GTL
66GTL
21GTL, 25GTL,
29GTL, 89GTL,
1000GTL, 78X
140GTL, 142GTL
YELLOW
(black)
AUDIO
#2
SHIELD
(shield)
526T Series I1
Model (others)
I
I
RING
AUDIO
AUDIO
#3
#2
WHITE
(white)
TIP
SLEEVE
ABBREVIATIONS
ELK
=
black
BLU
=
blue
BRN
=
brown
CHAS
=
chassis
CKT
=
circuit
CTR
=
center
GND = ground
GRN
=
green
Hi = high
#3
#1
#2
#3
# I
GND
# l
GND
GND
#1
#1
SLEEVE
#2
#4
#1
# I
#2, 4
#2
#2
NC
LO
=
low SW
=
switch
LS = loudspeaker
V
=
volt
MIC
=
microphone VIO
=
violet
NC
=
no connection WHT
=
white
ORN
=
orange XMTR
=
transmitter
PWR SPLY
=
power supply YEL
=
yellow
RCVR = receiver Z = impedance
Rev
=
revised
SHLD = shield
TIP
CB-950, CBH-990
CB-515, -555, -725,
-910, -930
CB-7200
CB-750
CB-775
CBR-9940
C BR-9600
CBR-9900
CB-920
CBR.9950
CB-770
CBM-6100
BROWNING
Brownie, LTD, SST
Mark II Series B,
SSB15
Eaglette
Eaglette II
SST-2, Brownie,
Sabre, Baron
Eagle S23, Golden
Eagle Mark II
(69R & 69T),
Golden Eagle
Mark Ill
Golden Eagle
Mark 4
28-75258
CADRE
526T Series I1
Model (others)
BOHSEI
Smokey
BOMAN
CKT GND
GND
#1
SLEEVE
WHITE
(white)
#1
NC
#4
#4
#2
#3
#3
#2
#3
#2
#4
#3
#4
#3
#1
RELAY
XMTR
#3
#2
#2
#3
NOTES
SHIELD
(shield)
#2
2,4
525 (500-1, 520);
510-A; 515; 510
CALTRON
CB-7500
CHANNEL MASTER
CB6832, CB6830,
CB6834, CB6835
CHRYSLER
4048076, 77
1. When using the 526T only (not the Series II) with this transceiver, cut the internal GRAY lead of the microphone.
2. When using the 526T only (not the Series Il) with this transceiver, cut the internal WHITE lead of the microphone from the
amplifier to the press-to-talk switch (see Figure 4).
3. When using the 526T only (not the Series II) with this transceiver, cut the internal BLUE lead. Refer to the Isolated
Switching section of the data sheet.
4. This transceiver requires a high-impedance audio input. When using the CB41, CB42, CB43, CB44, and CB45, the GREEN
audio lead replaces the WHITE audio lead.
5. This transceiver requires an isolated switching contact when using the CB41, CB42, CB43, CB44, and CB45. Refer to the
Isolated Switching section of the data sheet for circuit modification instructions (see Figure 3).
6. This transceiver is recommended for use only with the 526T Series II.
7. When using the 526T Series II with this transceiver, the YELLOW lead is not used.
8. This transceiver is not recommended for use with Shure Citizens Band microphones.
9. This transceiver is recommended for use only with the 526T Series II after special internal modifications are made. Refer
to the data sheet, or write to Shure Brothers Incorporated.
#2
#2
$4
#1
#4
#3
#1
#3
#2
#2
#2
#1
SHELL
CKTGND
GND
#4
SHELL
#3
#4
YELLOW
(black)
#3
#2
#1
#2
#I
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
RED
(red)
#4
1, 2
1, 2
1, 2
1, 2
1,2
2
2
2
1, 2
1, 2
2
8
4
3, 4, 5, 7
1,2
2
4
4
2
#3
#2
#4
#3
BLUE
#2
#4
#3
# I
NC
BLACK
NC
#1
#4
#3
#2
Notes
1, 2
#3
#2
#4
#3
NC
NC
NC
NC
2
1, 2
2