Shure 526T Series II Wiring Manual page 10

526TSeries 111 WHITE
I
SHIELD
I
YELLOW
1
RED
I
BLUE
1
BLACK
1
Notes
Model (others) (white)
1
(shield)
526T Series II
Model (others)
(black)
E. F. JOHNSON
4170, 4175
Viking 352, 352D,
4740
Messenger 4230, 40;
Viking 230, 430
Viking 4740
Viking 200
Messenger 92/40,
Viking 4330, 4360
Messenger 80 (242-
0080), 50 (242-
0050-01)
Messenger 4730
YELLOW
(black)
WHITE
(white)
KRACO
KCB-1307
KCB-2320, -2340,
-4010, -4020,
-4030
KCB-4070
KCB-4088
KCB-4060, -4090,
-4095
KCB-4W3
KCB-4004
KCB-4005,
-4001, -4045
KCB-4000
KRlS
T23B, 99er, Vega
23
+
Valiant, Ventura
Victor, Victor II
XL.23, XL25, XL30,
XL50
XL70
XL23A
XL45
BLACK SHIELD
(shield)
#4
#2
#2
#2
#2, 4
# I
#2
SHLD
Notes RED
(red)
BLUE
#5 #2
#2 #6
BLU RED
# I
# I
WHT
VIO
#6
#6
SHLD
RED
KAAR
TR336 (SkyLark I),
TR337 (Skyhawk 1 1 )
611 17TR3331B,
1211 11 7TR333lB,
321TR333B
TR327lAlB
TR335 (Skyhawk)
-
KENWOOD
TR-7400A
TR-7600
TR-8300, T-599
TS-IPOS, .120, -180
TS-520, -5205, -820
TS-700SP
GND
#4
#2
#2
#2
#4
#2
#2
RELAY
#2
#3
#3
#3
WHT
I
CKTGND
CKT GND
SLEEVE
CKT GND
SLEEVE
#4
#4
NC
#3
#2
#3
#3
#5
NC
NC
LS CKT-
ELK
LAFAY ETTE
HE-640
LM-100, Dyna.Com 3C,
LM-300
Comstat-525
Telstat 1050,
SSB-I40
HE-4000
Telstat 1240,
Dyna.Com 40
LM-200
LM-400
Comstat 19, 23, 23
Mark V, 35;
HB-400; HB-444;
HB-444125A
Comstat 23, 25A,
258
Comstat 23 Mark VI
HE-23, HE-502,
HE-502A, Micro 12,
Telsat SSB-25
#3
#2
#3
#4
#2
#2
#2
#4
#4
GND
#4
#3
#2
#3
#4
#2
#2
#2
#4
#4
GND
#4
#2
#4
#2
#4
GND-SHLD
#2
#3
#4
#2
SHLD
SHLD
K MART
D40
KNIGHT
KN-2500, KN-2550,
KN-2580, KN-2585
KN-2526, KN-2565,
KN2567
KN-2560
KN-2590
KRACO
KCB-2320A,
KCB-2310A,
KCB-2330B
KCB-2370
KCB-1401
KB-2355
KCB-1300
KCB-2390
x w r ~ c K T .
1
GNLLD
RED
# I
#3
# I
# I
AUDIO-
WHT
# I
#5
# I
# I
Y EL
Y EL
#3
NC
NC
#3
BLK
VIO
ABBREVIATIONS
NOTES
wHT RED
I
2:;
1. When using the 526T only (not the Series Ii) with this transceiver, cut the internal GRAY lead of the microphone.
2. When using the 526T only (not the Series 1 1 ) with this transceiver, cut the internal WHITE lead of the microphone from the
amplifier t o the press-to-talk switch (see Figure 4).
3. When using the 526T only (not the Series 1 1 ) with this transceiver, cut the internal BLUE lead. Refer to the Isolated
Switching sectlon of the data sheet.
4. This transceiver requires a high-impedance audio input. When using the CB41, CB42, CB43, CB44, and CB45, the GREEN
audio lead replaces the WHITE audio lead.
5. This transceiver requires an isolated switching contact when using the CB41, CB42, CB43, CB44, and CB45. Refer t o the
lsolated Switching section of the data sheet for circuit modification instructions (see Figure 3).
6. This transceiver is recommended for use only with the 526T Series 1 1 .
7. When using the 526T Series I1 with this transceiver, the YELLOW lead is not used.
8. This transceiver is not recommended for use with Shure Citizens Band microphones.
9.
This transceiver is recommended for use only with the 526T Series I1 after special internal modifications are made. Refer
to the data sheet, or write t o Shure Brothers Incorporated.
ELK
=
black
BLU = blue
BRN
=
brown
CHAS
=
chassis
CKT
=
circuit
CTR
=
center
GND
=
ground
GRN
=
green
HI
=
high
LO
=
low SW = switch
LS
=
loudspeaker V
=
volt
MIC = microphone VIO
=
violet
NC
=
no connection WHT = white
ORN
=
orange XMTR
=
transmitter
PWR SPLY
=
power supply YEL = yellow
RCVR = receiver Z
=
impedance
Rev
=
revised
SHLD
=
shield