Shure 526T Series II Wiring Manual page 12

526T Series II
Model (others)
526T Series II
Model (others)
WHITE
(white)
SHIELD
(shield)
CKT GND
#2
#3
#6
#2
#2, 4
#2
#3
#2
#2
#2
#2
WHITE
(white)
YELLOW
(black)
BLUE
CKT GND
#2
#3
#6
#2
#4
#2
#3
#2
#3
#2
#2
SHIELD
(shield)
BLACK Notes
1, 2
1, 2
1 , 2
1, 2
8
1, 2
1, 2
1, 2
1 , 2
1, 2
2, 3, 5, 7
8
2, 4
2
YELLOW
FIE;
(black)
MIDLAND
13-801, 13-854
13-976; 76-858,
-863; 77-825,
-830, 857
76-886
77-838, -849
77-861, -899
77-883
77-892
77.8240, 79-891,
150M (77.150),
200M (77.200),
3001 (77-003),
4001 (77-004)s
5001 (77-005),
6001 (79-006),
7001 (79-007)
100M
77-963, -8246,
-821, -856, -859,
-101 B; 78-574;
76-860, 78-999,
77-101C
79-893
63-445; 77-889,
-861 8; 79-900
13-509
13-510, -510A. -513
NUVOX
CB-7000
TC-5020
BLUE
RED
#1
#1
#2
#1
#1
#1
# I
#1
#1
# I
# I
BLK
#3
#5
#12
#4
#3
#3
#5
#3
#3
NC
NC
BLACK
OLSON
CB-88, RA-717
RA-590 (Side Bander
1 1 )
CB-23, RA-530
RA-590
CB-409
Notes
AUDlO
#1
XMTR
#3
RING
AUDlO
#1
TIP
XMTR
#3
PACE
TA2300lB
2300 (Early Model)
2300 (After 5172
with 5 pin plug),
P2376, 2376A
2300 (New model
with 4 pin plug)
I, li, 11-s, 100,
200, Plus 23
8003,8340
144, 8047, 8092,
8117, IOOOMC,
CB166C
8014
8113
8016
FM152
8093, 8155, 8193
3230, 3275
CB-185; 8041,8046
2300C
8008
CBST-23 (Side Talk
23), 130, Side
Talk 1000B,
IOOOM, CB113,
CB145, CB166,
CB162, CB161
CB-76
lOOASA
100s
102, 123, 123A
# I
AUDIO
#5
#4
XMTR CKT
#2
AUDlO XMTR CKT
MOPAR
40941 73
4094176, 4094177,
4094178. 4094179
MOTOROLA
T4000A, T4005A,
T4010A, T4020A,
T4025A, T4009A,
CT950AX
CF925AX
CB40
NDI
PC-101, -102, -200
PC-201
MORSE I ELECTRO-
PHONIC
CB700, CB800, 3005
CB2000
2001
W 4
#4
#4
AUDlO
#1
#2
'
#1
1
RELAY
#1
#1
#1
NOTES
1. When using the 5267 only (not the Series II) with this transceiver, cut the internal GRAY lead of the microphone.
2. When using the 526T only (not the Series Ii) with this transceiver, cut the internal WHITE lead of the microphone from the
amplifier to the press-to-talk switcb (see Figure 4).
3. When using the 5265 only (not the Series II) with this transceiver, cut the internal BLUE lead. Refer to the Isolated
Switching section of the data sheet.
4. This transceiver requires a high-impedance audio input. When using the CB41, CB42, CB43, CB44, and CB45, the GREEN
audio lead replaces the WHITE audio lead.
5. This transceiver requires an isolated switching contact when using the 12041, CB42, 12843, CB44, and CB45. Refer to the
Isolated Switching sectlon of the data sheet for circuit modification instructions (see Figure 3).
6. This transceiver is recommended for use only with the 526T Series II.
7. When using the 526T Series II with this transceiver, the YELLOW lead is not used.
8. This transceiver is not recommended for use with Shure Citizens Band microphones.
9. This transceiver is recommended for use only with the 526T Series II after special internal modifications are made. Refer
to the data sheet, or write to Shure Brothers Incorporated.
10. Connect pin 2 to Shell.
ABBREVIATIONS
BLK = black
BLU
=
blue
ERN = brown
CHAS = chassis
CKT
=
circuit
CTR = center
GND = ground
GRN
=
green
Hi = high
#2
#2
#2
LO = low SW = switch
LS = loudspeaker V = volt
MiC
=
microphone VlO = violet
NC = no connection WHT = white
ORN
=
orange XMTR = transmitter
PWR SPLY
=
power supply YEL
=
yellow
RCVR = receiver Z = ~mpedance
Rev
=
revised
SHLD = shield
#3
#4
NC
#4
#3
#3
#2
#2
#2