1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Dishwasher
  5. SW260
  6. Manual

Smeg SW260 Manual

Professional
Hide thumbs Also See for SW260:
Table of Contents

Advertisement

Quick Links

Read all the instructions in this manual carefully to become familiar with the right
This manual is an integral part of the dishwasher and must always be kept intact together with the
appliance. Before using the appliance, please read this manual throughout. Installation must be done
by qualified staff in compliance with the relevant regulations. The appliance is intended for
professional use, and complies with Directives 2006/95 EC and 2004/108 EC, including the prevention
and elimination of RF disturbance. The appliance is built to provide the following function: Washing
and drying dishes; all other uses are to be considered improper. The manufacturer declines all
liability for uses other than those stated above.

1 PRODUCT IDENTIFICATION AND SAFETY AND OPERATING WARNINGS

1.1 Brand and model (or type)

Professional dishwasher
Brand: Smeg
Model: SW260/262

1.2 Edition (revision) of user manual

1.3 Name and address of manufacturer/distributor

Smeg S.p.A.
Via Leonardo da Vinci, 4 - 42016 Guastalla (RE) Tel. +39 0522 8211 - Fax + 39 0522 821453 website:
www.smegfoodservice.com,
Info :
INFORMATION AND SERVICE FOR SMEG PROFESSIONAL DISHWASHER PRODUCTS
Our Sales Department staff will be able to provide you with information about prices and special offers.
Our After-Sales Department will be able to provide you with guidance about keeping your appliance
functioning correctly and put you in touch with your nearest authorised Service Centre. Our entire product
offering can be viewed at the above website.

1.4 Declaration of conformity to product standards

This appliance is marked in compliance with European Directive 2002/96/EC on waste electrical and electronic
equipment (WEEE). Make sure that this product is scrapped correctly to safeguard the environment and
health. Decommission the appliance in compliance with local waste management regulations. For further
information on the treatment, recovery and recycling of this product, contact the local authority, domestic
waste collection service, or your Smeg reseller. The appliance must be connected to earth in compliance with
electrical safety (CEI-EN-IEC 60335-2-58/61770) and electromagnetic compatibility regulations (CEI-IEC-EN
55014-1/-2, 61000-3;4, 50366). The manufacturer is not liable for any injury or damage cause by failure to
comply with the instruction given in this manual, improper use, tampering with even a single part of the
appliance, or the use of non-original spare parts.
SMEG thanks you for choosing one of
its products.
conditions for the proper use of your dishwasher.
19 390 5043 04
Rev. of manual
email : foodservice@smeg.it
10/05/2016
Date
1

Advertisement

Table of Contents
loading

Related Manuals for Smeg SW260

Summary of Contents for Smeg SW260

  • Page 1: Product Identification And Safety And Operating Warnings

    Smeg reseller. The appliance must be connected to earth in compliance with electrical safety (CEI-EN-IEC 60335-2-58/61770) and electromagnetic compatibility regulations (CEI-IEC-EN 55014-1/-2, 61000-3;4, 50366).

  • Page 2: Product Characteristics

    2 PRODUCT CHARACTERISTICS 2.1 Application, general functions and intended use Dishwasher intended exclusively for professional use, must be used by authorised and trained staff. Designed for washing tableware (plates, cups, bowls, oven dishes and cutlery) and similar catering items, and complies with international electrical and mechanical safety codes.
  • Page 3 BUILD-UNDER INSTALLATION fig. 2 – Diagram, build-under IMPORTANT Models equipped with condensers must be supplied with cold water in the specified temperature range if the condenser itself is to work properly BACK PANEL CONNECTIONS Description Hot water supply hose (red collar) Cold water supply hose (blue collar) Power supply cable Steam condenser drain hose (as applicable)

  • Page 4: Technical Characteristics (Power, Plumbing)

    INSTALLATION WITH BASE If the appliance is installed on a base which raises it off the ground (e.g. the Smeg B6040), of height HB (height of base), all height dimensions relative to ground level indicated in this document must be increased by the said amount HB.

  • Page 5: Plumbing Connections

    CAUTION – MAINS WATER HARDNESS To be done by the user: check the mains water hardness. Only if the hardness of the mains water is known can the Smeg technician set the dishwasher's parameters for the integrated water softener. You should run regular checks (e.g. once or twice a year) of the mains water quality to ensure that the initial values are maintained and adjust the dishwasher's settings if necessary.
  • Page 6 fig. 6 – Diagram, the drain connections may be made on the right or left of the appliance, while accounting for the maximum clearance indicated by the product Dimension “I” DRAIN TYPE AND DIMENSION “H” ABOVE Distance of drain from side of N.

  • Page 7: Noise

    General instructions for installing the drain Make sure to use a drain with siphon. When installing the drain connection, take the following precautions:  Since the drain water temperature can be as high as 95°C (models with thermodisinfection), the end of the drain hose must be fixed permanently to the hose fitting, using the provided hose clamps.
  • Page 8 For further information on the treatment, recovery and recycling of this product, contact the local authority, domestic waste collection service, or your Smeg reseller. Do not use equipment which has been damaged during transport! In case of doubt, contact your reseller.

  • Page 9: Symbols

    Replace any faulty parts only with original spare parts. The manufacturer is not liable in any way for damage resulting from the use of unauthorised spare parts. The manufacturer declines all responsibility for injury or damage caused by failure to comply with the above regulations or deriving from tampering with even just one part of the appliance and the use of non-original spare parts.

  • Page 10: Installing The Appliance

    corners, cover. Wooden and cardboard components can be disposed of in accordance with the relevant regulations. 4.3 Installing the appliance The dishwasher must be installed by an authorised technician. Do not install a dishwasher which has been damaged during transport. Do not install the dishwasher near to sources of heat (e.g. gas burners, stoves, fireplaces, etc.) since they can damage it.

  • Page 11: Operator And Technician Authorisations

    The appliance may only be installed, serviced or repaired by a technician authorised to do so by the Manufacturer. Repairs done by unauthorised persons not only void the warranty but may be hazardous to the user. Only use original Smeg spare parts when replacing components. 4.6 Precautions before use First start-up The electrical protection system must undergo a functional test before the appliance is put into operation.

  • Page 12: Operating Information And Instructions

    Never touch the heating elements in the tank. Contact authorised Smeg technical staff in case of malfunction. 5.2 Using the water softener The quantity of lime in the water (which indicates its hardness) causes whitish marks on dry dishes and dishes also tend to lose their shine over time.

  • Page 13: Using Detergent And Rinse Aid

    Correct use of the peristaltic pumps – OPTIONAL WARNING The peristaltic pumps must be installed by a technician authorised to do so by Smeg. After installation, they must be enabled (see SET-UP) In this case, do not use the door dispenser; the machine must be hooked up to the detergent (red hose) and rinse aid (transparent hose) containers.

  • Page 14: Tank Level Sensors - Optional

    (there is a sensor connection for each peristaltic pump). This must be done by a technician authorised to do so by Smeg. fig. 11 – Configuration with LEVEL SENSOR: Detergent intake nozzle with integrated level sensor. The intake nozzle is fitted with a filter; make sure this is always properly located to prevent lumps being drawn up.

  • Page 15: Description Of Controls And Wash Programs

    Check from time to time that the silicone hose is properly secured to the stainless steel intake pipe, and that there are no leaks. Use proper clamping equipment (such as plastic pull ties) to secure the silicone hose to the stainless steel pipe. 5.4 Description of controls and wash programs 5.4.1 Controls...
  • Page 16 BUTTONS DESCRIPTION Fast old down: show the remaining time Once on, the dishwasher displays the program ID (e.g. “Pr 03”). When the interface is switched off, the display reads “OFF”. When the door is open the display shows four dashes and the other buttons are disabled. If the dishwasher is switched off with the water in the tank, the “OFF”...

  • Page 17: Indicator Light - Meaning

    5.5 Indicator light – Meaning fig. 12 – In the display area of the control panel: central digit area and indicator light around the perimeter ON THE Led symbol Meaning DISPLAY No detergent (only if the level sensor is installed in the container) No rinse aid (only if the level sensor is installed in the container) No salt:...

  • Page 18: Loading Tableware

    may have caused the event as an aid to troubleshooting. Record all alarms and inform technical service accordingly in case of need. 5.6 Loading tableware 5.6.1 Example loads Bottom basket Top basket fig. 13 – Example loads 5.7 Height adjustment of the upper basket 5.7.1 Adjustment procedure The upper basket’s height can be adjusted so that dishware of great dimensions can be placed in the lower...
  • Page 19 1) Extract the basket. 2) Open the retaining clip on both rails (see white circle). 3) Extract it and put in position again by 4) Close the retaining clip on both rails. inserting the upper wheels in the rail (see white circle).

  • Page 20: Setting The Wash Program

    9) Height of the funnel before adjusting it. 10) Height of the funnel after adjusting it. 5.8 Setting the wash program 5.8.1 Models SW262 Depending on the type of dirt and the amount of tableware loaded into the baskets Powder detergent PROGRAM Type of soiling (when a detergent peristaltic...

  • Page 21: Models: Swt262

    * ONLY IF PERISTALTIC PUMP INSTALLED (WITH STANDARD DOSE) Important: If the Repeat function is enabled, leave the door ajar after unloading the dishes if the appliance is not to be reused at once; if it is out of use for some time, perform a pump-out cycle before reusing it to prevent foaming.

  • Page 22: Model Swt260X E Swt260

    5.8.3 Model SWT260X e SWT260: CONTROL PANEL SWT260X CONTROL PANEL SWT260 Depending on the type of dirt and the amount of tableware loaded into the baskets Powder detergent PROGRAM Type of soiling (when a detergent peristaltic pump is not installed) Specifically for glasses 15 grams Lightly soiled dishes, washed immediately after use.

  • Page 23: Drying Cycle

    Table’s value are referred to machine working with 400V 3N~ electric and 55°C hot water supplies and with no load inside. If Repeat is enabled, leave the door slightly open after unloading the tableware if the machine is not to be used again immediately; if the pause is very long, run a drain cycle first to prevent foaming.

  • Page 24: Perform Resins Regeneration

    5.12.1 Perform resins regeneration. When “R” light is on, we suggest to perform as soon as possible a complete drain phase; in this way the machine will regenerate resins automatically . NOTE – PROGRAM RUN TIMES The run times displayed on the control panel are approximate; the temperature and pressure of the water supply will affect the actual duration, among other factors.

  • Page 25: Running A Reset Procedure

    5.14.1 Running a RESET procedure In case of alarm or with the dishwasher stopped: press and hold down the Start/Pause and DRAIN buttons together for 2 seconds, until a beep sounds. The display reads "P-" and the RESET starts. At the end of the procedure, the display flashes "E-" alternating with the program number, if you are resetting a previously interrupted program, or “End”...

  • Page 26: Parameter "Set 3

    POSSIBLE POSSIBLE DESCRIPTION TECHNICIAN PARAMETER USER ACTION ACTION Detergent pump P1 batching. Set the ml/l, the default setting is 3 = 3 ml/l. 1 – (The max. setting is 10 = 9.8 ml/l) Increase/decrease the setting with the Select buttons. Rinse aid pump P2 batching.

  • Page 27: Cloc Menu

    SET 3 Value °f °d (default) 22.5 6.1.4 Cloc menu The display reads Cloc. The “Cloc” menu (an abbreviation of “CLOCK”) is used to set the current date and time. The parameter can be set with a user password as well. Proceed as follows: a.

  • Page 28: Cleaning And Routine Maintenance

    At the end of the warranty period and every year thereafter and whenever message A 93 displays, contact your Smeg authorised service centre for a complete check-up. Maintenance work not covered by the warranty, which does not cover replacement of parts subject to normal wear and tear.
  • Page 29 Water intake filter A on the cock must be cleaned from time to time; this should be done 1 every 2 – 6 months, depending on the quantity of water used. Close the water supply cock, unscrew the end of the water intake hose, remove filter A and clean it carefully under running water.

  • Page 30: Description Of Maintenance And Cleaning By The Authorised Technician

    fig. 16 – Chamber drain filter, disassembly procedure and view of parts. External circular filter To remove this filter:  Take hold of the conical filter's tabs and turn anticlockwise (box A).  Without pressing the tabs, lift the assembly (box B). When cleaning this filter, the others should also be cleaned.

  • Page 31: Alarms

     The dishwasher filters are not clogged. 3. If the load is not properly cleaned, check that:  The correct amount of detergent has been added.  The salt container is not empty.  The tableware has been loaded correctly. ...
  • Page 32 1. Close the water supply cock. 2. Disconnect the machine from its power supply. 3. Check that the machine is properly hooked up (water and power) and that the initial installation conditions have not changed. 4. Contact Smeg technical service. ALARM ID DESCRIPTION USER ACTION The water does not heat to User: run the DEFAULT PROCEDURE described above.
  • Page 33 ALARM ID DESCRIPTION USER ACTION Run the checks and procedures specified in AF:11. Also check for leaks - check for water on the floor around the Not enough water. Tank water AF:23 machine. level is dropping. If you find any leaks: immediately close all supply cocks and contact technical service.
  • Page 34 ALARM ID DESCRIPTION USER ACTION Make sure to close the door properly before running a wash cycle. Try opening the device again with the Open door button. Door lock fault, no automatic AF:56 If necessary, use the manual door release procedure open.

  • Page 35: Table Of Contents

    8 INDEX PRODUCT IDENTIFICATION AND SAFETY AND OPERATING WARNINGS ..........1 Brand and model (or type) ........................1 Edition (revision) of user manual ......................1 Name and address of manufacturer/distributor ..................1 Declaration of conformity to product standards..................1 PRODUCT CHARACTERISTICS ........................ 2 Application, general functions and intended use ..................
  • Page 36 5.4.2 Detailed description ........................15 Indicator light – Meaning ........................17 Loading tableware ..........................18 5.6.1 Example loads ..........................18 Height adjustment of the upper basket ....................18 5.7.1 Adjustment procedure ........................18 Setting the wash program ........................20 5.8.1 Models SW262 ..........................
  • Page 37 INDEX ..............................35...

This manual is also suitable for:

Sw262

Table of Contents