BOMANN EBK 960 Instruction Manual page 6

Household induction hob

Hide thumbs Also See for EBK 960:

Instruction manual (16 pages)

Table Of Contents

Table of Contents

Enlarged version

Preparing the worktop for installation of the hob

Preparing the worktop for

CAUTION:

Before cutting secure the outer cutout

adhesive tape to avoid traces of jigsaw on the work-

adhesive tape to avoid traces of jigsaw on the

top.

• The worktop must have a minimum thickness of

30 mm, it must lie horizontally and be sealed to

must lie horizontally and be sealed to

the wall side against overflowing liquids or mois-

the wall side against overflowing liquids or moi

ture.

• The cut surfaces (cutout edges) must be sealed

with special varnish, silicone rubber or cast raisin

in order to prevent swelling caused by humidity.

• Clean and dry the worktop in the cutout area

Clean and dry the worktop in the cutout area

thoroughly.

Worktop cutout

Prepare the cutout of the worktop according to the

dimensional drawing.

Figures in mm

Installing the hob

• First check the factory fitted hob seal

First check the factory fitted hob seal at the hob

frame to the integrity and the proper fit.

• Put the hob with the connecting cable

Put the hob with the connecting cable first and

with the control panel to the front into the pr

control panel to the front into the pre-

pared cutout.

• Make sure that the distances to the cutting are

Make sure that the distances to the cutting are

equal on all four sides and that the seal is resting

on the worktop.

• Fix the hob depending on the worktop thickness

Fix the hob depending on the worktop thickness

by attaching the enclosed brackets (3)

installation of the hob

cutout edge with wide

minimum thickness of

dges) must be sealed

according to the

1 1 1 1

Hob

2 2 2 2

Gasket

3 3 3 3

Bracket

4 4 4 4

Screw

brackets (3) from the

hob bottom at the provided holes and fasten them

with the screws (4).

Electrical connection

Information for the authorized expert

Information for the

authorized expert

Information for the

authorized expert

WARNING:

• The installation to the mains supply must conform

The installation to the mains supply must conform

to the local standards and regulations.

• Connecting the appliance to a domestic power

appliance to a domestic power

socket or using multiple sockets or extension ca-

socket or using multiple sockets or extension c

bles is not permitted.

• Improper connection may cause to an

Improper connection may cause to an electric

shock

shock!

shock

• Before connecting, ensure that the power supply

Before connecting, ensure that the power supply

corresponds with the information on the rating la-

corresponds with the information on the rating l

bel (appliance bottom) an

• Fix the mains cable in the tension relief.

Fix the mains cable in the tension relief.

• The electrical installation must have an isolation

The electrical installation must have an isolation

device which lets you disconnect the appliance at

all poles from the power supply.

all poles from the power supply. The disconnect

device shall be executed with a contact width of

min. 3 mm.

• Arrange the mains cable in such a way that it

Arrange the mains cable in such a way that it

does not get in contact with any hot components

of the appliance. Do not lead it over sharp edges

or corners.

Mains socket

The socket must be connected according to the

standards to a single-pole circuit breaker. The co

nection is shown below:

NOTE: : : :

NOTE

L1-brown L2

L2-black P3

) and the wiring diagram.

ted with a contact width of

pole circuit breaker. The con-

P3-green-

-yellow N1

N1-blue N2

electric

N2-grey

Table of Contents

BOMANN EBK 960 Instruction Manual page 6

Related Manuals for BOMANN EBK 960

Related Products for BOMANN EBK 960

Table of Contents