Advertisement
Quick Links
Advertisement
Related Manuals for Wideye iSavi-E
Summary of Contents for Wideye iSavi-E
- Page 1 QUICK START GUIDE iSavi-E Version 1.0...
-
Page 2: Getting Started
Quick Start Guide. Copyright © 2016 Addvalue Innovation Pte Ltd. All rights reserved. Addvalue, the Addvalue Enabled logo, Wideye, the Wideye logo, iSavi and iSavi logo are either trademarks or registered trademarks of Addvalue Technologies Ltd and/or its affiliates in Singapore and/or other countries. -
Page 3: Regulatory Information
Addvalue Innovation Pte Ltd., 8, Tai Seng Link, Level 5 (Wing 2), Singapore 534158. declares under our sole responsibility that the Product, brand name as Wideye and model: iSavi-E, SH-100E Satellite terminal to which this declaration relates, is in conformity with the following standards and/or other normative documents: ETSI EN 301 489-1, -19, -20, ETSI EN 301 681, EN 62311, ITU-R M.1480... - Page 4 WELCOME Congratulations on purchasing the Addvalue Wideye™ iSavi-E satellite terminal. QUICK REFERENCE Antenna Pointing LEDs Battery Pack Power Button Exit Pointing Mode Button Transceiver Elevation Angle Indicator Battery Power DC Power Input Indicator Button Connector Cover Other contents in the box...
- Page 5 GETTING STARTED STEP 3 STEP 1 Insert the Micro-SIM card with its gold-contacts Pull the handle of the micro-USB connector as facing down. shown to unplug the connector cable. Handle Connector Cable Note: Ensure your iSavi™ is off before removing or installing the SIM card.
- Page 6 STEP 5 Use a finger to press the latch and ensure that the transceiver is properly attached to the terminal. STEP 6 Insert the charger lead and then plug the adapter into a suitable power source. Your iSavi™ should be charged for 8 hours before first use.
- Page 7 STEP 7 STEP 9 Tilt the terminal to 45 degrees. Plug in the micro-USB connector. STEP 8 Attach the Ethernet adapter. STEP 10 Place your iSavi™ outside in a position with an unob- structed view of the sky. Press and hold the power button for 5 seconds to switch on your iSavi™.
- Page 8 POINT THE TERMINAL AND CONNECT TO NETWORK Method 1: LED Visual Pointing Mode STEP 1 Make sure you place your iSavi™ in the open air, with an unobstructed view of the sky. Your iSavi™ needs to be pointed towards the satellite in the correct direction to ensure connection to the satellite network. Note: In some cases , you might encounter magnetic interference.
- Page 9 POINT THE TERMINAL AND CONNECT TO NETWORK LED Visual Pointing Mode Magnetic Interference Occasionally, if your iSavi is in close proximity to ferrous objects, the sensors will have difficulty determining its correct orientation. If the LEDs display any other When this happens, the LEDs will flash in the following sequence : pattern of illumination refer to the LED Status Quick Reference Guide for...
- Page 10 POINT THE TERMINAL AND CONNECT TO NETWORK Method 2: Audio Assisted Pointing Mode STEP 1 STEP 3 To switch into audio assisted pointing mode, Turn the terminal slowly in clockwise or press and hold the ‘Exit Pointing Mode Button’ counterclockwise until the beeping frequency for 5 seconds when your iSavi™...
-
Page 11: Accessing Data
ACCESSING DATA STEP 4 STEP 1 Once your iSavi™ is connected to the network, Insert the Ethernet cable to the Ethernet it will automatically activate the data session. adapter as shown below. To stop access to data, press ‘Deactivate data connection’. - Page 12 POWERING DOWN AND DETACHING THE BATTERY STEP 1 STEP 4 Remove the Ethernet cable from the ethernet The powering down process takes about 20 adapter. seconds. Wait until all the LEDs are off. STEP 5 Pull down the battery latch in the direction as shown.