Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for sky rider Micro
Summary of Contents for sky rider Micro
- Page 1 User’s Guide for Model DR107 v1736-02...
- Page 3 Warnings & Precautions Important Safety Instructions • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and • Read and follow all instructions. receiver. • Keep these instructions for future reference. • Connect the equipment into an outlet on a circuit •...
-
Page 4: Table Of Contents
Table of Contents SkyRider Micro – 5 Flying Tips & Features – 14 Features Tips for Safe Operation Includes Speed Setting Flips & Tricks Overview – 6 Headless Mode Craft Layout & Features Auto-Reverse Remote Control Repair – 16 Batteries & Charging – 8... -
Page 5: Skyrider Micro
SkyRider Micro Features • 360° flips & tricks • 6-axis gyroscope • 3 speeds • Control distance: up to 98 feet • LED navigation lights • Operating time: 4-5 minutes • Charge time: 20 minutes Includes • 2.4 GHz remote control: requires 2 AAA batteries (not included) •... -
Page 6: Overview
Overview Craft Layout & Features LED Formation Lights Blue LEDs indicate the front of the craft. Power Switch (side) Charging Port (rear) -
Page 7: Remote Control
Remote Control Remove thumbsticks from the storage compartment and insert into the controls. Left Control Stick Right Control Stick Increase Throttle: Pitch: push forward push forward/backward Decrease Throttle: Roll/Bank: pull backward push left/right Yaw/Spin: push left or right Power Switch & Status Indicator Flip Speed Setting... -
Page 8: Batteries & Charging
Batteries & Charging Battery Charging Procedure The craft’s battery must be charged before the unit can be flown. Before charging, be sure the craft and remote control are powered OFF. Failure to do so may result in injury or damage. Connect the charging cable (included) to the USB port of a powered ON computer or USB power adaptor (not included), then connect the charging plug to charging port on the unit. -
Page 9: Remote Control Batteries
Remote Control Batteries Use included screwdriver Remove Battery Cover 2 x 1.5V AAA... -
Page 10: Flying
Flying Craft/Remote Link Before flying, the craft and the remote must be linked together and the gyroscopes on the craft must be allowed to calibrate. Begin with the craft and remote powered off. Step 1 Place the craft on a flat, level surface. This is necessary for the craft’s gyroscopes to properly align. - Page 11 Step 4 Push the Left Control Stick directly forward, then backward. A chime will sound when the craft is calibrated and ready to fly. Step 5 Push the Left Control Stick (throttle) forward to take off. Use both thumbsticks to control the craft. If you notice a tendency to drift, you may need to adjust the trim controls to fine tune the handling (see next section).
-
Page 12: Trim Adjustment
Trim Adjustment Setting Trim & Countering Drift Adjusting the trim settings to correct drift and provide better control of the craft. To avoid potential damage, adjust the trim while attempting a stable hover. Try to avoid making any exaggerated movements with the flight controls and adjust one trim setting at a time to avoid confusion. -
Page 13: Reset
Reset If the craft is still experiencing difficulty flying or is behaving erratically, the craft and remote may need to be reset to default settings. Be sure that the remote and craft are linked and begin on a flat level surface. Reset by simultaneously pulling both Control Sticks in the manner shown below. -
Page 14: Flying Tips & Features
Flying Tips & Features Tips for Safe Operation • Only fly in large, open spaces free of obstacles like power lines, trees, ceiling fans, etc. • It is best to fly 2 to 3 ft. from the ground and any obstacles. Flying low to the ground directs turbulence from the rotors back towards the craft, making it more difficult to control. -
Page 15: Flips & Tricks
Flips & Tricks Before attempting any stunts, be sure that there is ample clear space around the craft, ideally 3 to 5 ft.. in every direction. It is not recommended to attempt to flip around or through any obstacles, as this may result in unintended damage. Press the Flip button once, then move Craft will perform flip in the the Right Control Stick in any direction. -
Page 16: Repair
Repair REMINDER: Pilots are responsible for any damage caused by improper use. Parts Replacement Standard parts such as extra batteries and remotes are available online for purchase when in stock. However, any non-standard parts such as cameras, screws, bodies, SD cards etc. can be ordered by placing an inquiry with our parts department at: partsinfo@dpiinc.com. - Page 17 FRONT Rotor B Rotor A Rotor A Rotor B Matching rotors should be diagonally opposed.
-
Page 18: Troubleshooting
Troubleshooting If you are experiencing problems using or flying the craft, consult this table. PROBLEM POSSIBLE CAUSES SOLUTION Craft does not • No power to remote • Check remote batteries, respond to controls. or craft. replace if needed. • Craft is out of receiver •... -
Page 19: Customer Support
Customer Support Contact Information Warranty Website: www.gpx.com See included 30 Day Warranty for warranty information. Warranty and Email Support: prodinfo@dpiinc.com the most up-to-date version of this User’s Guide can also be found at: Email Parts: partsinfo@dpiinc.com http://gpx.com/dr107.html Phone Support: 1-888-999-4215 International Support To download this User’s Guide in English, Spanish, and French, or to get answers to frequently asked questions, visit the support section at: www.gpx.com...