Table of Contents
Advertisement
Introduction
The manual test mode can be used for testing the RF and audio
sections of the base unit and handset. The manual test mode is
also required for the FCC testing in which the phone is tested for
interference at the first, middle, and last RF channels.
The following features are provided in manual test mode.
• Able to set operating mode of the combo chip.
• Able to mute or unmute the audio path.
• Able to change the RF channel. (Both RX and TX)
• Able to transmit or receive data packet.
• Able to synchronize the security code.
BASE UNIT
1. Entering the Manual Test Mode
[#], [2], [1], [1], [0]
1. Press the key sequence
ON.
2. When enter the test mode, the
[INTERCOM]
LED light up, and happy tone is emitted.
2. Default Settings
• Channel set to 14. (out of 0 to 29)
• Combo set to active mode.
• Speakerphone unmute.
• TX audio path unmuted.
• RX audio path unmuted.
• TX power ON.
• Off hooked.
• Date transmission disabled.
3. SPEAKERPHONE Key Operation
1.
[1]
Condition: Press the
key.
Operation: Toggle transmitter on/off, it only turn the TX power
on/off with no modulation.
Indication: Beep tone is emitted.
2.
[2]
Condition: Press the
key.
Operation: Toggle TX mute, it only toggle the TX path of combo
chip.
Indication: Beep tone is emitted.
3.
[3]
Condition: Press the
key.
Operation: Toggle mic mute pin, the mic mute pin defalt value in
test mode is high (mute).
Indication: Beep tone is emitted.
4.
[4]
Condition: Press the
key.
Operation: Toggle HF path switch function, the HF pin will be
toggle.
Indication: Beep tone is emitted.
5.
[5]
Condition: Press the
key.
Operation: Toggle RX mute function, it only toggle the TX path
of combo chip.
Indication: Beep tone is emitted.
6.
[6]
Condition: Press the
key.
Operation: Toggle spk mute pin, the spk mute pin defalt value in
test mode is low (unmute).
Indication: Beep tone is emitted.
SECTION 4
TEST MODE
just after power
[SPEAKERPHONE]
LED and
7.
[7]
Condition: Press the
key.
Operation: TX data on, it only send security code change command
out if the transmitter power ON.
Indication: Beep tone is emitted.
8.
[8]
Condition: Press the
key.
Operation: Base DTMF test, it will send the dight 3 DTMF to line.
Indication: Beep tone is emitted and DTMF 3 gen. in line.
9.
[9]
Condition: Press the
key.
Operation: Stop DTMF test, it will stop the DTMF to line.
Indication: Beep tone is emitted and stop DTMF.
10.
[0]
Condition: Press the
key.
Operation: Base will receive the handset security code change
command and toggle the
Indication: Beep tone is emitted and
11.
[*]
Condition: Press the
key.
Operation: Stop the data transmit, but don't turn the TX power
OFF.
Indication: Beep tone is emitted.
12.
[#]
Condition: Press the
key.
Operation: Increase the current channel to next, if 30 back to 1.
Indication: Beep tone is emitted.
13.
[REDIAL/PAUSE]
Condition: Press the
Operation: Generate current ringer.
Indication: Beep tone and ringer tone are emitted.
14.
[FLASH]
Condition: Press the
Operation: Toggle hook pin, the hook pin defalt value in test mode
is low (hook off).
Indication: Beep tone is emitted.
15.
[HOLD]
Condition: Press the
Operation: Rewrite the EEPROM defalt value, ringer=1, flash
type=3 dialing type=tone, security code=000, last
channel=1.
Indication: Beep tone is emitted.
16.
[INTERCOM]
Condition: Press the
Operation: Toggle telsw pin, the telsw pin defalt value in test mode
is low.
Indication: Beep tone is emitted.
17.
[PGM]
Condition: Press the
key.
Operation: Enable the base to reprogram the security code. After
[PGM]
press the
key, the base will wait the security
code change command within 2 second. If received,
the base security code will be reprogram.
Indication: Beep tone is emitted and if received the command
gen.happy tone is emitted after reprogram security code.
SPP-N1025/N1026
[LINE]
LED.
[LINE]
LED is flashed.
key.
key.
key.
key.
9
Advertisement
Table of Contents
