Download
Share
Print this page
Dynojet POWER COMMANDER V Installation Instructions
  1. Manuals
  2. Brands
  3. Dynojet Manuals
  4. Automobile Accessories
  5. POWER COMMANDER V
  6. Installation instructions

Dynojet POWER COMMANDER V Installation Instructions

2009 ducati desmosedici
Hide thumbs Also See for POWER COMMANDER V:
1
2
3
4

Advertisement

Quick Links

Download this manual See also: Installation Instructions & Owner's Manual, Instruction and Installation Manual
2009 Ducati Desmosedici
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
14-007
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
2
Velcro strips
1
Alcohol swab
2
Zip ties
2
Posi-taps
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2009 Ducati Desmosedici - PCV - 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the POWER COMMANDER V and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dynojet POWER COMMANDER V

Summary of Contents for Dynojet POWER COMMANDER V

  • Page 1 USB Cable 2009 Ducati Desmosedici Installation Guide Power Commander Decals I n s t a l l a t i o n I n s t r u c t i o n s Dynojet Decals Velcro strips Alcohol swab Zip ties Posi-taps THE IGNITION MUST BE TURNED...
  • Page 2 POWER COMMANDER V INPUT ACCESSORY GUIDE ACCESSORY INPUTS Map - (Input 1 or 2) The PCV has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can USB CONNECTION use any open/close type switch. The polarity of the wires is not important. When using the Autotune kit one position will hold a base map and the other position will let you activate the learning mode. When the switch is “CLOSED” Autotune will be activated. (Set to Switch Input #1 by default.) Shifter- (Input 1 or 2) These inputs are for use with the Dynojet quickshifter. Insert the wires from the CRANK Dynojet quickshifter into the SHIFTER inputs. ANALOG The polarity of the wires is not important. (Set to Switch Input #2 by default.) SPEED EXPANSION PORTS 1 & 2 INPUT 2 (Grnd)
  • Page 3 FIG.A Remove the seat and fuel tank. Remove the left side fairing. Mount the PCV to left side inner panel, using the supplied Velcro (Fig. A). Make sure to use the alcohol swab to clean both surfaces before attaching the Velcro. FIG.B Unplug Locate the throttle body sub-connector on the left side of the air box (Fig. B). Unplug this connector by turning counter-clockwise. Ground wire FIG.C Plug the PCV wiring harness in-line of the stock wiring harness and throttle body sub-harness (Fig. C). 14-007 www.powercommander.com 2009 Ducati Desmosedici - PCV - 3...
  • Page 4 Locate the Throttle Position Sensor connector on FIG.D the left side of the throttle bodies. This is a 3-pin connector located to the inside of the frame. Unplug this connector from the throttle bodies to gain access to the wires. Using one of the supplied Posi-taps attach the GREY wire from the PCV to the stock ORANGE wire of the TPS harness (Fig. D). Using the other supplied Posi-tap, attach the BLACK/ WHITE wire from the PCV to the stock PURPLE/ BLACK wire of the stock TPS connector (Fig. D). FIG.E Plug the stock TPS connector back onto the throttle bodies. 10 Route the PCV harness along the left side of the engine and go towards the battery (Fig. E). 11 Use the supplied zip ties to secure the PCV harness to the main wiring harness. FIG.F 12 Route the PCV ground wire along the stock ground wire and secure it to the negative (-) terminal of the bike’s battery (Fig. F). PCV ground 13 Reinstall the bodywork, the seat, and the fuel tank. 14-007 www.powercommander.com 2009 Ducati Desmosedici - PCV - 4...