C. Batteries ......5 Operating Your JV35 A. Dialing ......7 B.
Page 3
Important Safety Instructions When using your telephone 8. Do not cover the slots and equipment, basic safety precautions openings on this telephone. This should always be followed to reduce telephone should never be placed the risk of fire and electric shock to near or over a radiator or heat persons, including the following: register.
Page 4
Important Safety Instructions E. If the telephone has been 13. To reduce the risk of electrical dropped or the case has shock, do not take this phone been damaged; apart. Opening or removing F. If the telephone exhibits a covers may expose you to distinct change in dangerous voltages or other performance.
Page 5
Important Safety Instructions with the above conditions may not sible. ADDITIONAL SAFETY NOTES FOR prevent degradation of service in some CANADIAN USERS situations. Repairs to certified equipment should be made by an The following items are included as authorized Canadian maintenance part of the CS-03 Requirements.
Important Safety Instructions WARNING: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalent Number is an indication of the maximum number of terminals allowed to be connected to a telephone interface.
Introducing the JV35 Thank you for selecting the exciting new JV35 from Clarity. It has been designed to meet the highest quality standards to provide you with years of convenient and trouble-free service. Please read these operating instructions thoroughly before using your telephone.
Package Checklist JV 35 PROG FLASH REDIAL BOOST TONE Handset Base Unit JV35 Telephone Line Cords USER GUIDE Handset Coil Cord Phone Base Plate User Guide DC Adapter Figure 1 - Package Components...
Features on the JV35 *Note: The Tone/Pulse switch can Ringer volume be found next to the telephone line control switch port. Audio output jack RINGER ANNOUNCE AUDIO Lo Med Hi Preset Prog Custom Output Announcement switch Emergency buttons JV 35...
Base Plate until it JV35. Then plug the snaps into place. AC Adapter into an electrical outlet. 4. Lift the handset and listen for a dial tone. 5. Your JV35 is ready to use. Fig. 5 - Phone base installation for wall mounting...
Installation 6. Lift the handset and 3. Plug in the short phone listen for a dial tone. cord. 7. Your JV35 is ready to 4. Insert the AC Adapter use. cord into the receptacle on the back of the JV35. Then plug the AC Adapter into an electrical outlet.
Page 12
Installation Insert 4 AA batteries here Press in here to open battery compartment Fig. 7 - Battery installation...
Operating your JV35 A. Dialing FLASH REDIAL PROG Pick up the handset and dial like BOOST any other telephone. As you dial, TONE Lo the numbers you are dialing will be announced (seven, five, two, Fig. 8 - BOOST Button etc.).
Operating your JV35 C. Adjusting The Tone Note: In standard use, the 1. When you hear a voice amplifier turns off whenever you on the line, press the hang up the telephone. This is a BOOST button. useful feature if many people use the phone.
Fig. 15 - Redial Fig. 14 - Flash Button Note: When the JV35 is on hold, if you pick up another phone that is on the same line, the JV35 will automatically hang up. You can continue your call on the other phone.
Operating your JV35 3. Press PROG button G. Programming the again. Emergency buttons The Emergency buttons can 4. Press one of the Emergency be programmed to dial buttons. numbers with one touch. You may wish to use these buttons for police, fire or medical response.
Operating your JV35 2. Enter the phone number H. Dialing With An Emergency as you would normally Button dial it. 1. Lift the handset. 2. Press one of the Emergency buttons. You will hear an announcement similar to “Emergency One” and then the number you have stored Fig.
Button Identification or to program another Announcements memory button, repeat this process from step 1. The JV35 comes with factory pre-recorded announcements to identify each Emergency button such as “Emergency One,” etc. You J. MEM Dialing can erase these identification announcements and record 1.
Page 19
Operating your JV35 4. After three seconds there will be a “beep” to tell you recording RINGER ANNOUNCEMENT AUDIO has stopped. Your recording will be played Lo Med Hi Preset Prog Custom OUTPUT back immediately so you Fig. 22 - Announcement Switch can check it, followed by a “beep-beep”...
“Program Mode, to tell you recording has Program Mode” followed stopped. Your recording by a “beep-beep” sound to will be played back confirm the JV35 is ready to immediately so you can be programmed. check it, followed by a “beep-beep” sound.
“Program Mode, button. Program Mode,” followed by a “beep- beep” sound to confirm RINGER ANNOUNCEMENT AUDIO the JV35 is ready to be Lo Med Hi Preset Prog Custom OUTPUT programmed. Fig. 27 - Setting Custom Announcements RINGER ANNOUNCEMENT AUDIO...
Page 22
Operating your JV35 3. Press the 1 button. 6. When you are finished After the “beep,” say “One” recording, hang up the in your own voice or handset. language. 7. Slide the Your recording can be up to one ANNOUNCEMENT second long.
Operating your JV35 To turn off the voice announce N. Selecting Number feature, turn the phone over Button Announcements and slide the “VOICE To hear the Number button ANNOUNCE” switch to OFF. announcements that were pre-recorded at the factory, slide...
A cochlear implant adapter cord is available from Plantronics that WARNING! During thunderstorms, can be used to plug the JV35 directly into a speech processor. avoid using telephones, as electric shock from lightning can occur.
Troubleshooting Chart If any problem should arise during operation of your JV35, go CAUSE AND PROBLEM CORRECTIVE through the suggestions listed ACTION below. Should the difficulty persist, contact Clarity or your Check all authorized dealer for assistance. phone cord No dial tone connections.
ACTA. A compliant telephone cord If this telephone equipment, the and modular plug, RJ11 USOC, is JV35 telephone, causes harm to provided with this product. It is the telephone network, the designed to be connected to a...
Page 27
If your home has specially wired Clarity at 800-426-3738. If the alarm equipment connected to the equipment is causing harm to the telephone line, ensure the telephone network, the telephone...