Table of Contents
Advertisement
Quick Links
eneo
is a registered trademark of Videor E. Hartig GmbH
®
Exclusive distribution through specialised trade channels only.
Videor E. Hartig GmbH
Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany
Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100
www.videor.com
Technical changes reserved
© Copyright by Videor E. Hartig GmbH
01/2011
Instruction Manual
Multifunctional CCTV Tester
Rapport III
Rapport III-Pro
Before attempting to connect or operate this product, please read these
instructions carefully and save this manual for future use.
Advertisement
Table of Contents
Summary of Contents for Eneo Rapport III
- Page 1 Instruction Manual Multifunctional CCTV Tester Rapport III Rapport III-Pro eneo is a registered trademark of Videor E. Hartig GmbH ® Exclusive distribution through specialised trade channels only. Videor E. Hartig GmbH Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100 Technical changes reserved ©...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Information ..............4 Before Using Rapport III ...........5 Safety Information............6 Product Introduction..........10 Major functions of Rapport III .........10 Standard item............11 Introduction ............12 Product Specification ..........18 General specification ..........18 Meter specification ..........19 Functional Specification..........20 Power ON/OFF ............20 Mode setup ............21 Video tester ............22... -
Page 3: Information
■ PTZ Control ■ Video Storage Function (DVR, Rapport If there are any questions which arise when using the Rapport III or the unit is III - PRO) damaged, please contact the supplier of your Rapport III. ■ Operating Temperature: -10T: ~ 50T: ■... -
Page 4: Safety Information
Precautions Precautions The following describes how to safely operate the Pay attention to the following precautions when using the Rapport III. Rapport III. Please read carefully "the precautions for use of this product" prior to ■ Do not use the unit in damp, humid or gaseous environments. - Page 5 SAFETY INFORMATION SAFETY INFORMATION Precautions Precautions Battery Charging Precautions Battery Handling The Rapport ill has a built-in Lithium ■ Avoid short circuits, as this will cause internal damage to the battery. ■ The soft packaging can easily be damaged by contact with sharp surfaces Polymer Battery.
-
Page 6: Product Introduction
Test, etc. ■ Power Adapter (DC12V) Rapport m-PRO) ■ Test Lead Set (1 x Red Lead, 1 x Black ■ Safety Strap Major Functions of Rapport III Lead) ■ BNC Video Cable ■ Rechargeable Lithium Polymer Battery ■ Video Testing (7.4V 2000mA) -
Page 7: Introduction
PRODUCT INTRODUCTION ■ Rapport III (without DVR function) Introduction The Rapport III and Rapport Ill-Pro support the same basic functions, but the Rapport III does not include the DVR function BNC Video Output BNC Video Input LED Indicator UTP Input RS-485 In/Out ■... - Page 8 PRODUCT INTRODUCTION PRODUCT INTRODUCTION Rapport III-Pro Rapport III Part Name Function Part Name Function À TFT LCD À TFT LCD Á POWER Red LED is on when the OSD POWER is on Á POWER Red LED is on when the OSD POWER is on Â...
- Page 9 Test Jack for UTP cable Generated Video Test Signals à SD Card SD Card Slot (Rapport HI-PRO)  Communication Connections for RS422 and RS485 Port Input & Output (Rx+, RX-, TX+, Tx-) à Safety Strap Used to Carry the Rapport III Safely...
-
Page 10: General Specification
PRODUCT INTRODUCTION PRODUCT INTRODUCTION General Specification Meter Specification Input Voltage 12V ±10%, above 1.2A Mode Range Minimum Accuracy Measuring Lithium Polymer Battery (Inner Battery packaging) 400mV 100mV ±(2.5% +4dgts) Electrical More than Charging Time Characteristics 6 hrs DC Voltage 10mV ±(2.5% +4dgts) Built-in Charger More than... -
Page 11: Functional Specification
VIDEO - METER - PTZ - CABLE - the product. After switching the power switch to the ON position, press SETUP the OSD button and the Rapport III will boot up. To turn the Rapport III ■ The MODE SELECT menu is displayed when the... -
Page 12: Video Tester
700 ± 140 mV Video and Testing: By default the Video will be displayed in the top portion of the screen. If there is no video signal at the VIDEO IN port of the Rapport III Colour Burst Level 300 ± 35 mV /Rapport HI-PRO "LOSS"... - Page 13 In an installation with multiple cameras, the video and sync levels should be matched as closely as possible at the head-end to prevent Selecting the DVR mode causes the DVR (Rapport III- PRO) to initially boot noticeable picture quality differences when switching between cameras on a sigle monitor.
-
Page 14: Dvr Function
FUNCTIONAL SPECIFICATION FUNCTIONAL SPECIFICATION 2. Basic Operation 1) Video Storing Function Recording video: Support 8 flies with 10minute each. - Input SD card: Input a SD card pre- Designate the file storage formatted to a FAT32 format. location using the Up & Down SD card slot OSD changes buttons. - Page 15 FUNCTIONAL SPECIFICATION FUNCTIONAL SPECIFICATION 2) Video Playback 4) Check Recorded File Shows the SD Card files, and their recorded file size. - Designate the file storage location by using the Up & Down keys and press the button. The play mode ( ►...
- Page 16 FUNCTIONAL SPECIFICATION FUNCTIONAL SPECIFICATION 3. Installation (Setup) How to playback the video file on a PC Please contact the manufacturer or your local agent to obtain the download details for the Rapport Ill-Pro PC playback software program. Supported PC spec. & O/S ITEM Min.
- Page 17 FUNCTIONAL SPECIFICATION FUNCTIONAL SPECIFICATION 4. AKR Player Screen You will find the Icon on your PC desktop after Precautions program set up ■ Insert SD Card as shown in the picture. Please make sure power is off Click the icon and AKR Play Screen starts. before inserting the SD Card.
-
Page 18: Digital Multimeter
Á Displayed - AC Voltage is indicated as RMS (Root Mean When using the meter function of the Rapport III, make sure the unit is Square) Values switched on and set to the appropriate test mode before connecting - The Measured Input value is Displayed in the the test lead set to the circuit under test. - Page 19 FUNCTIONAL SPECIFICATION FUNCTIONAL SPECIFICATION ■ ■ Measuring Resistance Measuring AC & DC Voltage The unit of resistance is the Ω. The meter sends a low current into the circuit so that the resistance can be measured. This current Voltage is the difference in electrical potential between two points. The runs along all paths between the two probes and enables the total polarity of an AC voltage varies with time, while DC polarity is constant.
-
Page 20: Ptz Controller
PTZ, connect the PTZ communications cables to TX terminals of Use the SETUP keys to adjust GPST / SPST / FUNC / SPD and the Rapport III. MENU settings (displayed on the lower part of the LCD screen) by pressing the SET key once. -
Page 21: Utp Cable Tester
PTZ ADDR: Setup the PTZ ID. The default ■ Connect the UTP cable to be tested to the UTP port of the Rapport III, and value is 001. To change the PTZ ID use the connect the other end of the cable to the yellow UTP test dongle. -
Page 22: Symbols
FUNCTIONAL SPECIFICATION TABLE 1 - SYMBOLS SETUP Mode Select: To access this menu Number Symbol Reference Description depress the key and select the IRE 60417 - 5031 Direct current SETUP icon. Select a menu Item by pressing the IRE 60417 - 5032 Alternating current keys. -
Page 23: Drawing
DRAWING (mm) MEMO...