Table of Contents
Advertisement
Quick Links
XX137-60-00
V910 IMPACT-RESISTANT
DOME CAMERAS WITH
WIDE DYNAMIC RANGE
Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet
your requirements or that the operation will be entirely error free or perform precisely as
described in the documentation. This system has not been designed to be used in life-critical
situations and must not be used for this purpose.
Copyright © 2009 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
Roughneck is a trademark of Vicon Industries Inc.
Dow Corning is a registered trademark of Dow Corning Corporation.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: +44 (0) 1489 566300
WEB: www.vicon-cctv.com
Vicon part number 8009-8137-60-00
Rev 109 Section 3
Advertisement
Table of Contents
Related Manuals for Roughneck V910A-WDR
Summary of Contents for Roughneck V910A-WDR
- Page 1 Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. Roughneck is a trademark of Vicon Industries Inc. Dow Corning is a registered trademark of Dow Corning Corporation. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788...
-
Page 3: Fcc Notice
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. - Page 4 Important Safeguards – Outdoor Use GRAPHIC SYMBOL EXPLANATION 13. Outdoor Cable Grounding - Use only grounded outdoor The lightening bolt symbol alerts the user to the presence of cables to protect against voltage surges and static charges. dangerous voltage that may present the risk of electric shock. Section 810 of the National Electrical Code, ANSI/NFPA 70- 1984, provides information on proper grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors...
-
Page 5: Table Of Contents
Camera/Lens Adjustments ..........................9 Switch Settings .............................9 Lens/Autoiris Adjustment ..........................9 Final Installation ............................10 Operation ...........................11 Maintenance ........................11 Shipping Instructions .......................12 Reference...........................13 Technical Information .......................15 Vicon Standard Equipment Warranty ................18 2BContents • i XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 6: Quick Installation
Quick Installation For complete detailed instructions on how to install the V910, read the Installation section. Installation Diagram ii • 3BQuick Installation XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 7: Introduction
Introduction The information in this manual covers the installation, operation, and maintenance of the Roughneck V910 Series of Impact-Resistant Dome Cameras. These units should only be installed by a qualified technician using common hand tools and approved materials and wiring methods in accordance with the national Electrical Code ANSI/NFPA 70, state and local wiring codes. -
Page 8: Installation
If the equipment must be returned for repair, follow the Shipping Instructions at the end of this manual. Roughneck V910 Dome Components The Roughneck V910 units consist of a base (which includes the camera mounting bracket with the camera/lens assembly) and a cover with a smoked dome. Refer to Figure 1. - Page 9 Figure 1 Exploded View 5BInstallation • 3 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR...
-
Page 10: Accessory Kit
Accessory Kit There is an accessory kit included with all configurations of Roughneck V910. The table below lists the contents. Description Quantity Tamperproof driver bit, ¼ hex T-15 (to remove tamperproof screws) Pipe sealant tape (to seal pipe fitting to housing) - Page 11 The varifocal lens can be manually adjusted for focus (near/far) and zoom (telephoto/wide). There is a potentiometer for adjustment for autoiris. When making adjustments, be sure 5BInstallation • 5 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR...
-
Page 12: Cable Connections
For the model using the twisted-pair video connection, use the twisted-pair video plug (provided in the accessory kit). Strip off approximately 0.25 in. (6 mm) of insulation from each individual wire. Attach each wire 6 • 5BInstallation XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 13: Fiber
A video adjustment cable is supplied in the accessory kit for adjusting the focus. Connect one end of this cable to J4 and the BNC connector to the camera. Refer to Figure 5B. Figure 5B 5BInstallation • 7 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 14: Camera Power Connections
The V910 has a heater in the base. Refer to Figure 1. The unit is delivered with the heater connection made to the connector (P4 on coax/UTP, J1 on fiber) on the PC board. Refer to Figure 5A or 5B, depending on version. 8 • 5BInstallation XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 15: Camera Synchronization
There is a potentiometer on the camera board to adjust the autoiris. Refer to Figure 7. Turning the potentiometer opens and closes the iris to regulate light extremes. Turning the potentiometer clockwise opens the iris wider, allowing more light. 5BInstallation • 9 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 16: Final Installation
Any alignment of holes and screws is acceptable. The cover can be rotated 90° by aligning the screws/holes differently. 10 • 5BInstallation XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 17: Operation
Operation When power is applied to the camera, the Roughneck V910 views the selected scene. Maintenance The Roughneck V910 Impact-Resistant Cameras require no scheduled maintenance except for the occasional cleaning of the lower dome. Care and Cleaning of Lower Dome The inside surface of the smoked (gray-tinted) dome is easily scratched. -
Page 18: Shipping Instructions
3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection. 4. Mark the R.A. number on the outside of the carton on the shipping label. 12 • 8BShipping Instructions XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... -
Page 19: Reference
820 (250) 1000 (300) 1600 (500) Best picture 400 (120) 530 (160) 820 (250) ** For longer cable runs, use a Vicon Video Amplifier to obtain a suitable picture. 9BReference • 13 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... - Page 20 Recommended Unshielded Twisted-Pair Cable Type Cable Type Wire Size Insulation Material Conductor Type Resistance (ohms) Number of (AWG) Twisted Pairs Belden1721X 24, Solid Polyethylene Bare Copper 14 • 9BReference XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR...
-
Page 21: Technical Information
*Note: Nominal power and current levels are calculated @ 24.0 VAC input line voltage. Maximum power and current levels are calculated @ 29.0 VAC input line voltage. 10BTechnical Information • 15 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... - Page 22 -40 to 150° F (-40 to 65° C). Storage Humidity: Up to 90% relative, noncondensing. Wind Load: Heavy rain or snow driven by winds up to 80 mph. (Not evaluated by UL) 16 • 10BTechnical Information XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR...
- Page 23 2:1 interlace, AGC on Iris Setting: ME/AE NTSC/PAL AGC: ON/OFF Lens Specifications Focal Length Field-of-View (mm) Horizontal Vertical 3.3 - 12 varifocal with autoiris 83.9° -.23.91° 61.9°- 17.93° 10BTechnical Information • 17 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR...
-
Page 24: Vicon Standard Equipment Warranty
WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE COMPANY’S WEBSITE, WWW.VICON-CCTV.COM. IN THAT EVENT, THE TERMS OF THE POSTED WARRANTY SHALL APPLY EXCLUSIVELY. Vicon Part Number: 8006-9010-03-06 Rev 1208 18 • 11BVicon Standard Equipment Warranty XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR... - Page 25 Notes 11BVicon Standard Equipment Warranty • 19 XX137-60-00 Rev 109 Roughneck V910 Dome Cameras with WDR...
- Page 26 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Germany vin-videotronic infosystems gmbh Lahnstrasse 1 D-24539 Neumuenster Phone: +49 (0) 4321 8790...