Table of Contents
Advertisement
Quick Links
X935-24-00
MODEL V894CSH CORNER-MOUNTED
AND V894WSH WALL-MOUNTED
SERIES OF HIGH- SECURITY CAMERAS
Copyright © 2008 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice
Vicon and its logo are registered trademarks of Vicon Industries Inc.
ExView is a trademark of Sony Corporation.
Loctite is a trademark of Loctite Corporation.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44 (0) 1489 566300
WEB: www.vicon-cctv.com
Vicon part number 8006-8935-24-00
Section 3 Rev 108
Advertisement
Table of Contents
Related Manuals for Roughneck Roughneck V894CSH
Summary of Contents for Roughneck Roughneck V894CSH
- Page 1 Copyright © 2008 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice Vicon and its logo are registered trademarks of Vicon Industries Inc. ExView is a trademark of Sony Corporation. Loctite is a trademark of Loctite Corporation.
-
Page 3: Fcc Notice
FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruction, may cause interference to radio and television reception. -
Page 4: Table Of Contents
Camera/Lens Positioning ..........................8 Final Installation Steps ..........................8 Maintenance........................8 Fuse Replacement ............................8 Coaxial Cable Recommendations ..................9 Shipping Instructions....................... 10 Technical Information ...................... 11 Vicon Standard Equipment Warranty ................14 ii • Contents X935-24-00 Rev 108 V894CSH/V894WSH High-Security Cameras... -
Page 5: Important Safeguards
Use only with a mounting accessory recommended by Vicon, or sold with the video product. Any mounting of the video product should follow Vicon’s instructions, and a mounting accessory recommended by Vicon should be used. - Page 6 Vicon or that have the other electric light or power circuits, or where it can fall same characteristics as the original part. Unauthorized into such power lines or circuits.
-
Page 7: Introduction
Introduction The information in this manual provides installation and maintenance procedures for the V894CSH Corner- Mounted and V894WSH Wall-Mounted Series of High-Security Camera/Housings. These units should only be installed by a qualified technician using approved materials in conformance with federal, state, and local codes. -
Page 8: Installation
Installation Unpacking and Inspection All Vicon equipment is inspected and tested before leaving the factory. It is the carrier’s responsibility to deliver the equipment in the same condition in which it left the factory. Inspection for Visible Damage Immediately inspect the cartons upon delivery. On all copies of the carrier’s freight bill, make a note of any visible damage. - Page 9 Corner Mount Wall Mount Figure 1 Installation Diagram Installation • 3 X935-24-00 Rev 108 V894CSH/V894WSH High-Security Cameras...
-
Page 10: Mounting The Housing
Item Quantity Function Rubber grommet Seals cable access hole against dust, prevents cable abrasion No. 8 Torx™ bit Use to remove and install tamperproof screws No. 8-32 tamperproof Torx screw Supplied as spares Cable tie mount, adhesive base Secures camera power cables Cable tie Secures camera power cables Table 2: Accessory Pack Contents... -
Page 11: Cable Connections
A UL listed Class 2 direct plug-in transformer with 24 VAC 200 mA output is required for powering the V894CSH and V894WSH cameras. Power Supplies Vicon recommends several power supplies, depending on the needs of the installation. Refer to the table below. For other multichannel power supplies, contact Altronix Corporation at 888-258-7669. Model Number... -
Page 12: Camera Synchronization
Camera Synchronization If there is more than one unit in a system, the cameras have to be synchronized to ensure there is no roll of video. If the camera will be used in a line lock video application, the camera interface board is already set in line lock mode by default. -
Page 13: Camera/Lens Adjustments
Camera/Lens Adjustments After all cabling is complete, the camera and lens can be adjusted. DIP Switch Settings Refer to Figures 2 and 3 when making DIP switch settings. (Note that the location of this DIP Switch is model dependent. Be sure to refer to the correct DIP switch, A or B, when setting.) The ELC/ALC mode switch is used to select Electronic Light Compensation or Automatic Light Compensation. -
Page 14: Camera/Lens Positioning
Camera/Lens Positioning The camera position can be adjusted in three axes, vertically (tilt), vertical height of the camera/lens assembly and rotation about the lens axis (roll). Swivel the assembly for tilt position. The vertical height of the camera/lens assembly can be adjusted by loosening the lock nut, changing the vertical position of the camera mounting bracket within the slot in the mounting bracket and retightening the nut. -
Page 15: Coaxial Cable Recommendations
Coaxial Cable Recommendations Caution: Careful selection of proper cable is essential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended, or equivalent, are installed. In all cases, coaxial cable impedance should be 75 ohms. -
Page 16: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. -
Page 17: Technical Information
Technical Information ELECTRICAL Input Voltage: 24 VAC ±20%, isolated input. Current Rating: 200 mA. Power Consumption: 4.8 W. Heat Equivalent: 0.27 btu/min (0.07 kg-cal/min). Note: These figures represent the conversion of 100% of the electrical energy to heat. Actual percentage of heat generated will be less and will vary from product to product. - Page 18 MECHANICAL Application: Indoor. Dimensions: Height: 4.5 in. (114 mm). Width: 4.0 in. (102 mm). Length: V894CSH: 5.5 in. (140 mm). V894WSH: 4.75 in. (121 mm). Weight: 2.75 lb (1.2 kg). Construction: Cover: stainless steel Internal Brackets: zinc-plated steel. Window: polycarbonate plastic. Finish: Satin brushed.
- Page 19 Technical Characteristic Camera V894CSH-3312(-C)/ V894CSH-3312DN(-C)/ V894CSH-2.6-6(-C)/ V894CSH-DN(-C)/ V894WSH-3312(-C) V894WSH-3312DN(-C) V894WSH-2.6-6(-C) V894WSH-DN(-C) Image Sensor 1/3 inch 1/4 inch 1/3 inch 1/4 inch Format Image Sensor Type ExView CCD ExView CCD TV System Standard 2:1 interlace; Standard 2:1 interlace; Standard 2:1 interlace; Standard 2:1 interlace;...
-
Page 20: 14 • Vicon Standard Equipment Warranty
Software supplied either separately or in hardware is furnished on an “As Is” basis. Vicon does not warrant that such software shall be error (bug) free. Software support via telephone, if provided at no cost, may be discontinued at any time without notice at Vicon’s sole discretion. - Page 21 Notes Vicon Standard Equipment Warranty • 15 X935-24-00 Rev 108 V894CSH/V894WSH High-Security Cameras...
- Page 22 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Germany vin-videotronic infosystems gmbh...