Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Bryston BP-17 cubed series
Summary of Contents for Bryston BP-17 cubed series
- Page 1 BP-17³ Cubed Series Preamplifier Owner’s Manual...
-
Page 2: Important Safety Instructions
As of 2006-02-22 Bryston will only warranty Bryston products purchased through authorized Bryston dealers. Bryston products with a date code of 0608 or higher (date code format is “yyww”, where “yy” is the two least significant digits of the year and “ww” is the week of the year) must be accompanied by a copy of the bill-of-sale from a Bryston authorized dealer to qualify for warranty service. -
Page 3: Table Of Contents
Table of Contents Important Safety Instructions ........2 General.................4 Welcome ..............4 Description ............4 Features ..............4 Shipping Box and Packing Material ......4 Installation ..............4 Ventilation .............4 Connecting to A/C Power ........4 Connecting to Audio Components ......4 Connecting Source Components......4 Connecting Amplification ........4 Optional Modules ............5 Moving Magnet Phono ..........5 Digital to Analog Converter (DAC) ......5... -
Page 4: General
General from Bryston for a small fee. Welcome Installation Thank you for your purchase of a Bryston Ventilation BP-17³ Cubed Series Stereo Preamplifier! This The BP-17³ is a cool-running line level component. new preamplifier is the first line-level component It generates far less heat than amplifiers and many to feature our patented Salomie buffer which other components. -
Page 5: Optional Modules
BP-17³ Cubed Series Preamplifier Using the DB9 female connector at the rear of the Optional Modules unit, the BP17 can receive commands via a straight- through cable at 9600 baud, 8 data bits, no parity The BP-17³ may be optionally equipped with a and 1 stop bit (9600,8,N,1). -
Page 6: Trigger Control
Bryston’s BR2. entered. To use a Bryston BR2 with the BP-17³, press the Inputs 1-4, Balanced Input 1 and Balanced Input PREAMP button. Volume and Mute remain active 2 can be selected by pressing the buttons that even when the remote is in D/A or CD mode. -
Page 7: Specifications And Dimensions
BP-17³ Cubed Series Preamplifier Specifications and Dimensions Frequency 20Hz - 20kHz: ± 0.05dB Response 1V rms Bal. In/Out: <0.0025% ≤0.0003% Noise <10Hz-20kHz, RCA IN/OUT: -102 dB relative to full output XLR IN/OUT: -108 dB Input Unbalanced: 6.5 kΩ Impedance Balanced (non inverting): 4.5kΩ... -
Page 8: Front Panel
DIGITAL Select PHONO ANALOG BAL 1 BAL 2 BALANCE MUTE BYPASS POWER HEADPHONE VOLUME will fully mute and the LED above that channel Front Panel will illuminate red. Balance does not affect the 1. Power / Standby record output. Press this button to toggle the BP-17³... -
Page 9: Rear Panel
7. IR Receiver source components. When equipped with an The BP-17³ can be controlled using Bryston’s optional digital to analog converter module, BR-2 or another remote control. Input 1 can be divided into two separate S/PDIF inputs, and TOSLINK optical digital 8. - Page 10 Master Fuse Compartment: The BP-17 is protected by an AC Mains fuse specifically rated for the AC power in your region. The fuse must be installed and in tact for the amplifier to power on and operate. Only replace the fuse with one of identical value. Do not attempt removal or replacement of the fuse when the amplifier is plugged into the wall!
- Page 11 BP-17³ Cubed Series Preamplifier This page intentionally left blank...
- Page 12 Bryston Limited | 677 Neal Drive | Peterborough, Ontario K9J 6X7 Canada | Phone: 705-742-5325 | www.bryston.com 08-28-2017 300068-5...
Need help?
Do you have a question about the BP-17 cubed series and is the answer not in the manual?
Questions and answers