Xinje VB3-20P7 User Manual page 92

V5 series inverter
P9.00 P9.00 P9.00 P9.00 Traverse Traverse Traverse Traverse operation
0 0 0 0 ：Disabled
Disabled Disabled Disabled
1 1 1 1 ：Enabled
Enabled Enabled
Enabled
P9.01 Traverse
P9.01 P9.01 P9.01 Traverse Traverse Traverse operation
Unit' ' ' ' s s s s place Unit Unit place place place of of of of LED LED LED LED：start mode
Unit
0 0 0 0 ：Auto
Auto mode Auto Auto mode mode mode. . . . The inverter will running at preset frequency (P9.02) for certain time (P9.03), and then enter the traverse
operation.
1 1 1 1 ：Manual
Manual Manual Manual mode mode mode. . . . If the multi-function terminal (Xi is set to No.25 function) is enabled, the inverter will enter traverse mode
mode. If the terminal is disabled, the drive will end traverse operation and operate at the pre-traverse frequency (P9.02).
Ten Ten Ten Ten' ' ' ' s s s s place place place of of of of LED place LED：Traverse operating amplitude LED LED
0 0 0 0 ：Variable
Variable Variable amplitude amplitude. . . . Traverse operating amplitude AW changes with the central frequency and the change rate is defined amplitude
Variable amplitude
by P9.04.
1 1 1 1 ：Fixed
Fixed Fixed amplitude amplitude . . . . Traverse operating amplitude AW is decided by max frequency and P9.04. amplitude
Fixed amplitude
P9.02 Pre-traverse
P9.02 P9.02 P9.02 Pre-traverse Pre-traverse frequency Pre-traverse
P9.03 Waiting time
P9.03 P9.03 P9.03 Waiting Waiting Waiting time time before time
P9.02 is used to set running frequency before inverter enter traverse state.
If you select auto start mode, P9.03 is used to set the holding time with pre-traverse frequency before the inverter enter
traverse state; if you select manual start mode，P9.03 is disabled. Refer to Fig. 4－45 for introduction.
P9.04 P9.04 P9.04 P9.04 Traverse operating amplitude
Variable amplitude：Aw＝Central frequency×P9.04
Fixed amplitude：Aw＝Max operting frequency P0.06×P9.04
Prompt：The traverse frequency will be limit by upper/lower limit of frequency, and the traverse operation will not work
abnormally with unsuitable setup.
P9.05 P9.05 P9.05 P9.05
As shown in Fig4-45, there is no jitter frequency if P9.05 is set to 0.
P9.06 P9.06 P9.06 P9.06 Traverse operating Traverse Traverse Traverse
It defines the time of a complete traverse operation cycle including rising and falling processes.
P9.07 P9.07 Rising time of trangle wave
P9.07 P9.07
Running time of traverse rising stage＝P9.06×P9.07(s)，Time of falling stage＝P9.06×（1－P9.07）(s)。Refer Fig.4－45
for introduction
Note：You can select S-curve Acc/Dec mode along with traverse so as to make the traverse operating more smoothly. Note Note Note
P9.08 P9.08 Reference Reference length length
P9.08 P9.08 Reference Reference length length
P9.09 P9.09 Actual Actual length length
P9.09 P9.09 Actual Actual length length
P9.10 P9.10 P9.10 P9.10 Times Times Times Times of of of of length length length length
correction correction coefficient coefficient of of of of coefficient
correction correction coefficient
P9.11 P9.11
P9.11 P9.11
length length length length
P9.12 P9.12 Perimeter Perimeter Perimeter of of of of shaft
P9.12 P9.12 Perimeter
P9.13 P9.13 Number of of of of pulses Number Number pulses pulses
P9.13 P9.13 Number pulses per
This group of parameters are used for fixed length control.
The drive inputs counting pulses via terminals (X6, defined as function 35), and calculate length according to the number of
pulses per revolution (P9.13) and perimeter of shaft (P9.12).
Calculated length＝Number of pulses÷number of pulses per revolution×perimeter of shaft
86
operation operation selection operation selection selection selection
operation control mode
operation control operation control mode control mode mode
frequency
frequency frequency
before pre-traverse frequency
before before pre-traverse pre-traverse pre-traverse frequency frequency frequency
Jitter Jitter Jitter Jitter frequency frequency frequency frequency
operating operating cycle operating cycle cycle cycle
shaft shaft
shaft
per per revolution revolution
per revolution revolution
Range Range：0 0 0 0 , , , , 1 1 1 1 Range
Range
Range Range Range Range：00 00 00 00～11 11 11 11
Range 0.00 650.00Hz
Range Range Range：0.00 0.00－650.00Hz 0.00 650.00Hz 650.00Hz
Range Range Range：0.0 Range 0.0 0.0 0.0－6000.0s 6000.0s 6000.0s 6000.0s
Range Range Range：0.0 Range 0.0～50.0 0.0 0.0
Range Range Range：0.0 Range 0.0 0.0 0.0～50.0
Range Range Range Range：0.1 0.1～999.9s 0.1 0.1
Range Range 0.0 0.0
Range Range：0.0 0.0～98.0
Range Range 0.000 0.000 65.535km 65.535km
Range：0.000 Range 0.000～65.535km 65.535km
Range 0.000 65.535km
Range Range：0.000 Range 0.000 0.000～65.535km 65.535km 65.535km
Range Range Range Range：0.001 0.001 0.001～30.000 0.001 30.000 30.000 30.000
Range Range 0.001 0.001 1.000 1.000
Range Range：0.001 0.001～1.000 1.000
Range Range 0.01 0.01 100.00(cm) 100.00(cm)
Range：0.01 Range 0.01～100.00(cm) 100.00(cm)
Range：1 1 1 1 ～9999
Range Range 9999 9999
Range 9999
50.0 50.0 50.0％
50.0 50.0 50.0％
999.9s 999.9s 999.9s
98.0 98.0
98.0％
0.000(km) 0.000(km)
0.000(km) 0.000(km)
0.000(km) 0.000(km)
0.000(km) 0.000(km)
10.00(cm) 10.00(cm)
10.00(cm) 10.00(cm)
0 0 0 0
0 0 0 0
0.00Hz
0.00Hz 0.00Hz 0.00Hz
0.0s
0.0s 0.0s 0.0s
0.0 0.0 0.0 0.0％
0.0 0.0 0.0 0.0％
10.0s 10.0s 10.0s 10.0s
50.0 50.0
50.0 50.0％
1.000 1.000 1.000 1.000
1.000 1.000
1.000 1.000
1 1 1 1