Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for xpr B100PROX-AH
Summary of Contents for xpr B100PROX-AH
- Page 1 B100PROX-EH(AH) Biometric Proximity Reader INSTALLER MANUAL...
-
Page 2: Table Of Contents
CONTENTS 1. DESCRIPTION 2. SPECIFICATIONS 3. MOUNTING 4. WIRING 5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER 5.1 CONNECTING BIOMETRIC READERS IN SAME RS485 LINE WITH THE EWS CONTROLLERS 5.2 CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION 5.3 RS485 TUNING 6. -
Page 3: Description
The coating on the surface of the TouchChip sensor provides protection from scratching and abrasion due to normal contact with fingertips and any incidental contact with fingernails. SPECIFICATIONS Fingerprint capacity up to 100 fingerprints Biometry and Proximity (125 Khz, EM or HID (B100PROX-EH); HID or AWID (B100PROX-AH, Technology selectable by dipswitch) Outdoors Authentication... -
Page 4: Mounting
(fitted with additional heater if very low temperature) to keep a constant sensor level performance. XPR™ cannot guarantee the functionality of the product if measures and advice before are not followed. -
Page 5: Connecting Biometric Readers To Ews Controller
CONNECTING BIOMETRIC READERS TO EWS CONTROLLER - The Biometric readers can be connected to virtually any controller that conforms to Wiegand format standards (standard Wiegand 26bit or self-defined Wiegand). - The lines D0 and D1 are the Wiegand lines and the Wiegand Number is sent through them. - The RS485 line (A, B) is used for fingerprint transfer and reader settings. -
Page 6: Connecting Biometric Readers When All The Controllers Have Tcp/Ip Communication
CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION TCP/IP Switch max. max. max. When all the controllers are connected via TCP/IP, then the RS485 network becomes local (from Reader 1 to the Controller then to the Reader 2). Connect the readers directly to the Rs485 terminals in each controller. -
Page 7: Connecting Biometric Readers To 3Rd Party Controller
CONNECTING BIOMETRIC READERS TO THIRD PARTY CONTROLLERS 3rd party controller 3rd party controller CNV100 - + D0 D1 - + D0 D1 - + D0 D1 - + D0 D1 CNV200 RS485 A USB Desktop Reader RS485 B CNV300 optional BIOMANAGER Software CNV1000 Connect the lines D0, D1, Gnd and +12V to the third party controller. -
Page 8: Configuring The Biometric Readers In Pros Cs Software
(right click on the portal/search devices/readers). (8.4 & 8.5) To check if the reader is On Line, right click on the reader and select “Check version”. In the Event Window a message should appear “Device ON Line, Type: B100-XX” (8.6) B100PROX-AH BIOC3... -
Page 9: Enrolling Fingerprints From A Reader
ENROLLING FINGERPRINTS FROM A READER 1. Open the Users Window and create a new user. Click on “New User”, put a name and ID(card number). (8.7) 2. Go to the “Biometric” Tab 3. Select the reader(with left click) from which the enrollment will be done. (8.8) 4. -
Page 10: Enrolling Fingerprints From Desktop Reader
ENROLLING FINGERPRINTS FROM DESKTOP READER Plug the Swipe Desktop Reader in the PC. If the device is not installed automatically use the drivers located on the CD provided with the Biometric reader. It is installed in the same way as a USB Device. When the desktop reader has been installed it will automatically appear in the Software. -
Page 11: Deleting Fingerprints
DELETING FINGERPRINTS In General, the fingerprints are stored in the Biometric reader and in the Software. Deleting can be done only in the readers or from both places. Deleting one user from the biometric reader Select the User Click on “Delete User”. The User together with its fingerprints will be deleted from both the software and the fingerprint readers. -
Page 12: Firmware Update
FIRMWARE UPDATE Right-click on the reader and select Firmware update menu (8.18) On the Firmware update window, click on the Browse button (8.19). The default location of the firmware files installed with PROS CS is in the folder "Firmware". Select the firmware file with a "xhc" extension. Click on the Upload button Important: Wait for the update end message. -
Page 13: Entry Mode
ENTRY MODE Card or Finger Right click on the biometric reader Select “Properties” and go to the “Biometric” tab For Entry Mode select “Card or Finger” (8.20) Note: All the fingers and the card will send the same wiegand number (8.21) 8.20 Card and Finger Right click on the biometric reader... -
Page 14: Configuring The Biometric Readers In Biomanager Cs
CONFIGURING THE BIOMETRIC READERS IN BIOMANAGER CS BIOMANAGER CS is software for fingerprint management of XPR Biometric readers, when used with third party access controllers. Main functions: - Fingerprint Enrollment It can be done by ANY Biometric reader in the network or by Desktop (USB) Biometric reader. -
Page 15: Edit Reader
If reader is online, new line is added on top of the event table If reader is not online, following line is added on top of the event table If reader is online, right click on reader and select Upload configuration Check at event table if configuration was successful EDIT READER Right-click on the reader and select Properties... -
Page 16: Add User
ADD USER 1. Open the Users Window and create a new user. Click on “New User”, put a name and ID(card number). (8.7) 2. Select the reader(with left click) from which the enrollment will be done. (8.8) 3. Right click on the fingertip and select enroll. (8.9) 4. -
Page 17: Deleting Fingerprints
DELETING FINGERPRINTS In General, the fingerprints are stored in the Biometric reader and in the Software. Deleting can be done only in the readers or from both places. Deleting one user from the biometric reader Select the User Click on “Delete User”. The User together with its fingerprints will be deleted from both the software and the fingerprint readers. -
Page 18: Custom Wiegand
CUSTOM WIEGAND BIOMANAGER CS has defined Wiegand 26, 30, 34, 40 bit as standard options and other 3 Wiegand settings as user definable. To setup custom Wiegand format Select Wiegand menu from Settings At Wiegand setup window select one from customs Wiegand Set Wiegand parameter Click on Save button Note:... -
Page 19: Wiegand Protocol Description
WIEGAND PROTOCOL DESCRIPTION The data is sent over the lines DATA 0 for the logic “0” and DATA 1 for the logic “1”. Both lines use inverted logic, meaning that a pulse low on DATA 0 indicates a “0” and a pulse low on DATA 1 indicates a “1”.When the lines are high, no data is being sent. Only 1 of the 2 lines ( DATA 0 / DATA 1 ) can pulse at the same time. -
Page 20: Safety Precautions
SAFETY PRECAUTIONS Do not install the device in a place subject to direct sun light without protective cover. Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna. Do not place the device near or above heating equipments. If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.