Polk Audio Digital Solution System Instruction Manual page 17

IMPORTANT NOTE:
The FM radio, AM radio, CD, and Tape audio inputs do not have
corresponding video inputs. When you select any of these sources,
you will see a blank screen on your TV (if your TV is on).
Surround Button
This button switches between the various surround sound modes and
2-channel stereo (except when the 6 Channel Audio input is used).
IMPORTANT NOTE: The Dolby Digital (AC-3) and DTS modes can be
selected only when either DSS Digital, cable Digital or DVD inputs are
selected. If you have selected a digital source with a Dolby Digital or
DTS soundtrack and you cannot get the 3/2.1 indicator on the display,
the most likely causes are:
1. The DVD player is not set to send out a 5.1 channel Dolby Digital or
DTS signal. In this case check the DVD player's operation manual.
2. The 5.1 soundtrack has not been selected on the DVD disc. In this
case press the disc menu button on your DVD player to access the DVD
disc's menu, and select either the Dolby Digital 5.1 or DTS 5.1
selections on the disc's set-up menu. Consult your DVD player's
operation manual for more information.
3. The DVD disc does not have a 5.1 surround soundtrack. This is
especially true of pre-1985 movies.
Multi-Room Button
Pressing this button switches the multi-room mode on and off. See page
25 for more information on using this feature.
▲▼
Tune Buttons
When either the AM or FM sources are selected, these buttons allow
you to manually tune in AM and FM radio stations. Pressing the ▲
button moves the tuner up the radio band. Pressing the ▼ button moves
the tuner down the radio band. The tuner stops as soon
as you release your finger from the button. See page 22 for more
information on using this feature.
Save Presets Button
When you want to select a radio station as a preset station, manually
tune to that station, press and hold the Save Presets button for 4 - 5
seconds. You will see the red
M E M O
the light stops flashing, the radio station has been saved and
M E M O
assigned the next available preset slot number. You may preset up to 50
radio stations. See page 23 for more information on using this feature.
Clear Button
When you want to clear a radio station from the list of presets, select
that preset station, then press and hold the Clear button until CLEAR
appears on the display. See page 23 for more information on using this
feature.
▲▼
Presets Buttons
These button select from the list of preset radio stations. Pushing the
▲ button moves from lower preset slots numbers to the higher preset
slot numbers. Pushing the ▼ button moves down through the list of
preset stations.
Aux Inputs Jacks
These auxiliary video/audio input jacks are revealed by removing the
oval rubber cover. They accept the connection of a camcorder, portable
VCR, or any other temporary source. To make proper connections, refer
the owner's manual of the auxiliary component.
Signal Strength Meter
This meter shows the relative signal strength of a radio signal. For best
reception, orient your antenna to get the maximum number of bars on
this meter.
light on the display flash. When
www.polkaudio.com
WHAT THOSE TEENY LITTLE LIGHTS MEAN
Test Tone Indicator
T E S T
This light illuminates when the surround sound balance test tone is
engaged. You should hear a "Ssshhhhh" noise from one speaker when
this is on. See page 20 for more information.
Memo Indicator
M E M O
This light illuminates when saving preset radio stations. See page 23 for
more information.
Auto Indicator
A U T O
Shows that the tuner is prepared to receive a stereo FM broadcast.
Tuned Indicator
T U N E D
This lights when a radio station has been properly tuned in.
FM Stereo Indicator
S T E R E O
Lights when a stereo FM broadcast is received.
Surround Mode Indicators
D T S
Indicates whether the system is delivering Stereo, Dolby Pro Logic,
Dolby Digital or DTS sound. See page 24 for more information.
Digital Input Indicators
Indicates which digital audio input is selected and operating.
Late Night Indicator
N I G H T
Indicates that the late night Dolby Digital compression circuit is
engaged. See page 23 for more information on this function.
Preset Scan Indicator
P - S C A N
Lights when the tuner is scanning through the radio station presets.
S T E R E O P R O L O G I C D I G I T A L
O P T C O A X 1 C O A X 2
17