5.
TO SET THE PRESSURE OF EACH CHAMBER IN YOUR GARMENT
5.1 With the pump off, press the "Power" On/Off button.
5.2 The pump will display the hours of usage for 5 seconds. While the hour meter is being dis-
played (first 5 seconds) Press and hold the "Up" and "Down" button at the same time and
hold them down for 5 more seconds.
5.3 The next set of numbers will show the current pressure setting in the "LED Readout" and
the chamber associated with that pressure in the "Chamber Number LED".
5.4 Change the pressure setting using the "Up" or "Down" button until you get to your desired
pressure.
5.5 Press the "Mode" button to move to the next chamber and repeat the steps above.
5.6 After you have set the pressure in all 8 chambers, press the "Power On/Off" button and
your pump will start to operate.
6.
PROGRAMMING YOUR PUMP TO OPERATE IN DIFFERENT MODES
The SC-3008-DL can run in a number of different modes, all of which are set in the following
manner:
6.1 With the Pump off, press the "Power" On/Off button.
6.2 The pump will display the hours of usage for 5 seconds. While the hour meter is being dis-
played (first 5 seconds) Press and hold the "Mode" button 5 more seconds.
6.3 After 5 seconds, you will see "1Hr." in the "LED Readout". This indicates that you are in the
Timed Shutoff mode. In this mode, the pump will operate for a set period of time between
10 and 120 minutes, then automatically turn off. The pump comes preset to this mode and
1 hour so there is no reason to go through these steps if you wish to run your pump in the 1
Hour Mode. If you would like to adjust the amount of time for treatment in the "Timed
Mode", simple press the up or down arrows while "1Hr" is showing to adjust the time.
Once your time setting is complete, press the "Power" On/Off button and your pump will
begin its cycle.
6.4 If you want to operate in a different mode, after "1Hr." shows press the "Mode" button
again and you will see "COn" which indicates you are in continuous mode. In this mode,
the pump will not shut off until you manually turn it off by pressing the "Power" On/Off
button. Once you see "COn", if you want to proceed with this setting, press the "Power"
On/Off button and your pump will begin its cycle.
6.5 Your pump comes with a "Pre-Therapy" treatment option. In this mode, the pump will run
for 10 minutes hitting only chambers 6,7,8 over and over again. After 10 minutes, the pump
will automatically go into either the 1 Hour mode or the Continuous mode depending on
how you set up your pump. The SC-3008-DL comes preset with the Pre-Therapy mode
turned off. To turn it on, during the Mode setup, press the "Mode" button again after 6.4
and you will see "PrE" in the LED Readout. While this is displayed, press the "Up" button to
change the number in the "Chamber Number LED" from 0 to 1. The "1" indicates that the
"Pre-Therapy" treatment has been activated, a "0" indicates that it is off. To move from 1
to 0, simply press the "Down" arrow. Once this is set, hit the "MODE" button again which
will return you to the 1 Hour Mode. Hit the "Power" button to start your pump in this
mode, or the "MODE" button again to move to the Continuous Mode. A Pre-Therapy treat-
ment can be used in either mode.
Please Note: The Pre-Therapy feature should not be turned on until the pump has run for
at least 10 minutes on a patient. This will give the pump time to learn the proper pressure
settings for each chamber.
11
Need help?
Do you have a question about the SC-3008-DL and is the answer not in the manual?